Войти:
Оценок - 1, средний балл: 5 ( )

Инструкция по эксплуатации Ariens, модель 96096000100

Производитель: Ariens
Размер: 2.18 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


11) • Release depth stake pin. Pull the depth stake up for increased tilling depth. Place depth stake pin in hole of depth stake to lock in position. • Place shift lever indicator in counter rotating ( ) till position . • Hold the tine control against the handle to start tilling movement. Tines and wheels will both turn. • Move throttle control to “FAST” position for deep tilling. To cultivate, throttle control can be set at any desired speed, depending on how fast or slow you wish to cultivate. IMPORTANT: ALWAYS RELEASE TINE CONTROL BEFORE MOVING SHIFT LEVER INTO ANOTHER POSITION. DEPTH STAKE PIN “RELEASED” POSITION TURNING • Release the tine control. • Move throttle control to “SLOW” position. • Place shift lever indicator in “F” (forward) position. Tines will not turn. • Lift handle to raise tines out of ground. • Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines. • When you have completed your turn-around, release the tine control and lower handle. Place shift lever in (till) position and move throttle control to de sired speed. To begin tilling, hold tine control against the handle. CULTIVATING • Use the forward rotating tine drive when cultivating, tilling soft ground or tilling pre-tilled soil. • Release depth and drag stake pins. Lower drag stake. Pull the depth stake up for increased tilling depth. Place proper pin in hole of depth stake or drag stake to lock in position. • Place shift lever indicator in forward rotating ( ) till position. • Hold the tine control against the handle to start tilling movement. Tines and wheels will both turn. • Move throttle control "FAST" position for deep tilling. To cultivate, throttle control can be set at any desired speed, depending on how fast or slow you wish to cultivate. • Always lower the drag stake when using the for ward rotating tine drive. OUTER SIDE SHIELDS (See Fig. 11) The back edges of the outer side shields are slotted so that the shields can be raised for deep tilling and low ered for shal low tilling to protect small plants from being buried. Loosen nut “A” in slot and nut “B”. Move shield to desired position (both sides). Retighten nuts. TO TRANSPORT depth_stake_11 NUT “B” NUT “A” OUTER SIDE SHIELD “LOCKED” POSITION CAUTION: Before lifting or trans porting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE YARD • Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in position. This prevents tines from scuffing the ground. • Place shift lever indicator in “F” (forward) position for transporting. Fig. 11 • Hold the tine control against the handle to start tiller movement. Tines will not turn. • Move throttle control to desired speed. AROUND TOWN • Disconnect spark plug wire. • Drain fuel tank. • Transport in upright position to prevent oil leakage. 8 OPERATION BEFORE START ING ENGINE IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN...

Эта инструкция также подходит к моделям:
Садовые инструменты - 21547000 (2.18 mb)
Садовые инструменты - 21547000 (2.18 mb)
Садовые инструменты - 21547000 (2.18 mb)
Садовые инструменты - 21547000 (2.18 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории