Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
P.O. Box 2810 Tualatin, Oregon 97062 Telephone 503 692-3070 FAX 503 692-6696 75RS75RSTM 2001 Shindaiwa Inc. Part Number 80045 Printed in U.S.A. Shindaiwa is a registered trademark of Shindaiwa, Inc. Part Number 80045 Notes Contents PAGE Introduction ........................................ 1 Assembly ............................................. 2 Operation ............................................. 4 Settings ................................................ 6 Rate Conversion ................................. 7 Maintenance ....................................... 8 Fasteners ............................................. 9 Illustrated Parts List ......................... 10 Warranty Statement ......................... 11 Introduction The information contained in this manual describes machines available at the time of production. While every attempt has been made to provide the very latest information about the 75RS, there may be some differences between your spreader and what is described here. Shindaiwa Inc. reserves the right to make changes in production without prior notice, and without obligation to make alterations to spreaders previously manufactured. If you have any questions regarding your 75RS Spreader, or if you do not understand something in this manual, your Shindaiwa dealer will be glad to assist you. For additional information, you may contact Shindaiwa Inc. at the address printed on the back of this manual. Prior to Assembly IMPORTANT! The terms “left,” “left-hand,” and “LH”; “right,” “right-hand,” and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation of the spreader. Before assembling the spreader, make sure you have all required components. See pages 9 and 10. ¦ Hopper assembly ¦ Drive wheel ¦ Free wheel ¦ Frame, axle and gearbox assy. ¦ Handle tube ¦ T-handle assembly ¦ Handle braces (2) ¦ Control rod and wire assembly ¦ Hardware bag (see page 9 for contents) ¦ This manual, part number 80045 Carefully inspect all components for damage. 75RS Specifications Dimensions Overall height ............ 22" (55.9 cm) Wheel track width ..... 22" (55.9 cm) Handle length ............ 31" (78.7 cm) Dry weight................. 18.3 lbs. (8.3 kg) Hopper capacity ..................................... ..... ................ 1.3 cubic feet (36.8 liters) Tires ..... 10" (254 mm) dia., pneumatic Axle bearing ................................. Nylon Frame............................7/8" (22.2 mm) (welded steel tube) Hex Bolt RH Handle Brace LH Handle 1/4-20 Hex Nut Hex Bolt RH Handle Brace LH Handle 1/4-20 Hex Nut Assembly 1/4-20 x 2 1/4 Figure 1 Brace 1. Remove the spreader and components from the carton and place the spreader upside down on a padded surface. Install the LH & RH handle braces to frame using four 1/4-20 x 2 1/4" hex bolts and nuts. Do not tighten at this time. See Figure 1. 5/32 x 1" Cotter Pin Free Wheel 2. Install drive wheel onto the right- hand end of the axle as viewed from the operating position. (You can identify the drive wheel by the cotter pin hole drilled in the hub). The hub must face towards frame. Align the hole in the drive wheel hub and the hole in the axle. Secure drive wheel to axle with the 5/32" x 2" cotter pin. Install the free wheel on the opposite end of the axle. Insert the 5/32" x 1" cotter pin to retain the free wheel. See Figure 2. 1/4-20 Hex Nut & Washer Figure 3 1/4-20 x 2 1/4" Bolt OFF ON 3. Feed control knob/wire through the T-handle until the caution label touches the round hole. See Figure 3. DO NOT COMPRESS THE SPRING AT THIS TIME. Feed the T-handle/control wire assembly through the square handle tube towards the locator dot. See Figure 4. Secure the T- handle to the tube with (2)1/4-20 x 2 1/4" bolts, (4) flat washers, and (2) hex nuts. See Figure 3. Handle Tube 1/4-20 Hex Nut Figure 4 4. Turn the spreader upright and install the handle tube with the dot between the handle braces as shown. Install (2) 1/4 x 1 1/2" hex bolts and nuts. See Figure 4. The feed control wire must be positioned above the handle brace bolts to operate properly. Securely tighten all nuts and bolts installed in previous steps. Shindaiwa Limited Warranty Shindaiwa Inc. manufactures its products to superior quality standards to afford our customers the highest level of satisfaction. In keeping with this goal, Shindaiwa Inc. warrants this HomePro 75RS Spreader to the original purchaser as follows: Warranty Period 1 year for Personal/Consumer use. 180 days for Commercial/ Institutional use. 90 days for rental use. Warranty Administration Within the covered warranty period, Shindaiwa Inc. will, at their option, repair or replace any defect in material or workmanship, without charge for parts or labor, if this product is presented at an authorized Shindaiwa dealer. Warranty Exclusions and Limitations Shindaiwa Inc. assumes no responsibility for damages, loss, or injury resulting from: Normal wear and tear. Misuse or neglect....
Эта инструкция также подходит к моделям:Садовые инструменты - 80045 (171.26 kb)