Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Slide the ignition switch to the “O” (Engine OFF) position. Checking Unit Condition NEVER operate the unit with the cutting attachment shield or other protective devices removed! Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit without written approval from Shindaiwa, Inc. ALWAYS make sure the cutting attachment is properly installed and firmly tightened before operation. NEVER use a cracked or warped cutting attachment: replace it with a serviceable one. Operation Shoulder strap WARNING! Always wear a shoulder strap or harness when operating this unit. Using a harness with a brushcutter allows you to maintain proper control of the unit and reduces fatigue during extended operation. 1. Hook the strap hook to the hanger on the outer tube. 2. Wear the shoulder strap so that the hook stays at your right hand side. 3. Adjust the length of the shoulder strap so that you can hold and operate the machine comfortably. ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attach- ment with new one and re-check. ALWAYS stop the engine immediately NEVER operate a unit with worn or damaged fasteners or attachment holders. WARNING! A cutting attachment shield OFF When the unit is turned off make sure the cutting attachment has stopped before the unit is set down. and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment. NEVER allow the engine to run at high RPM without a load. Doing so could damage the engine. IMPORTANT! Adjust the shoulder strap so the shoulder pad rests comfortably on the offside shoulder and the cutting path of the cutting attachment is parallel to the ground. Make sure all hooks and adjustment devices are secure. NOTE: Using a shoulder strap when operating this unit with a blade allows you to maintain proper control of the unit and reduces fatigue during extended operation. IMPORTANT! or other protective device is no guarantee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS! Shoulder straprequired for usewith Brushcutters Operation (continued) Cutting grass with a trimmer head Your Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for specific applications and/or operational requirements. NOTE: For proper operation, always refer to the instructions accompanying the trimmer head being used. Trimmer head styles: Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation. Manual. The operator indexes line manually with the grass trimmer stopped. Fixed. The operator must stop the unit and add new lengths of trimmer line manually. Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to the head by pivots. NOTE: Additional hardware may be required to mount the Fixed Line or the Flail type trimmer heads. Operation (continued) Using a blade WARNING! ¦ Before working with a blade- equipped unit, always inspect and clean the area of objects that could interfere with or damage the blade. ¦ Never use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or damage. ¦ Never use a blade for purposes other than those for which it was designed. Engine Operating Speeds Operate at full throttle while cutting grass. CAUTION! Operation at low rpm can lead to premature clutch failure. Trimming and Mowing Grass Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut. To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line. Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer head horizontal. CAUTION! Do not push the rotating line into trees, wire fences or any material that could tangle or break line ends. CAUTION! Use only flexible, nonmetallic line recommended by the manufacturer. Never use, for example, wire or wire-rope, which can break off and become a dangerous projectile. ¦Whenever you strike a hard object with a blade, always stop the brushcutter and carefully inspect the blade for damage. NEVER OPERATE THE BRUSHCUTTER WITH A DAMAGED BLADE! ¦ A blade-equipped unit must be equipped with a bicycle-type handlebar or barrier bar as well as a harness or shoulder strap. ¦ Always make sure the cutting attachment shield is properly installed before operating this unit. Cut from left to right Cut Return WARNING! Remove all objects such as rocks, broken glass, nails, wire, or string, which can be thrown or become entangled in the cutting attachment. CAUTION! ¦ Operation of trimmer without a cutting attachment shield and using excessive line length can lead to premature clutch failure. ¦ Operation at low rpm can lead to premature clutch failure. Brushcutter Shoulder Strap A shoulder...
Эта инструкция также подходит к моделям:Садовые инструменты - C282 (1.8 mb)
Садовые инструменты - C282 (1.8 mb)
Садовые инструменты - C282 (1.8 mb)
Садовые инструменты - C282 (1.8 mb)