Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Note the location of the clutch cable guide. 4. Tighten all bolts and nuts. 5. Assemble the throttle control to the underside of the panel. Secure the cable to the left handle bar with the clip supplied. 6. Assemble the clutch spring to the clutch lever on the handle bar. Crimp lightly so it cannot come off. 7. Route the loop in the end of the clutch cable down through the two cable guides and attach it level on the idler arm weldment. Attach the chain on the other end to the spring on the clutch lever. Select a loop that will stretch the spring slightly when the clutch lever is pulled against the handle bar. 8. With the throttle control in the “OFF” position and the clutch lever released, pull the engine starter rope several times to be sure that the tines do not turn. 4 Figure 3 IMPORTANT ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. DO NOT START ENGINE WITHOUT ADDING OIL. Ref Part Qty Description 1 130670 1 Rear Support Assembly 3 400265 1 Screw, 3/8” - 16 x 1 1/2 8 162034 1 Wheel Yoke Assembly 13 162031 2 Wheel 14 359330 2 Bolt, Wheel 16 444721 3 3/8” Center Locknut 18 460312 2 Hairpin 19 461466 2 Pin, 3/8” x 2 1/8” Clevis 21 336685 1 Drag Stake Hitch Assembly Illustration 2 Ref. Part Qty Description 1 162007 1 Throttle Control Assembly 2 336677 1 Support LH 3 336676 1 Support RH 4 130698 1 RH Handle Assembly 5 313786 2 Grip 6 130699 1 LH Handle Assembly 7 130731 1 Handle Cross Brace 8 400186 2 Screw 5/16 - 18 x 1” Hex 9 446136 4 Lockwasher 5/16 Heavy 10 443106 4 Nut, 5/16 - 18 Hex 11 402014 2 #10 x 3/8” Slot Tapping Scr. 14 162029 1 Cable and Chain Assembly 15 359346 1 Clutch Locking Pin 16 359359 1 Spring 17 359327 1 Spring 18 359326 1 Clip 19 359345 1 Pin 20 336683 1 Lever 21 400208 2 5/16 x 18 x 1 3/4 Hex Cap Handle Bar Assembly -- Illustration 2 9 Drive Assembly Illustration 1 Ref. Part Qty Description Ref. Part Qty Description 1 359328 1 Belt, V-Drive 2 408883 3 Screw, 1/4” - 20 x 1/2” Hex Cap 15 443109 3 Nut 3/8” - NF5 Hex 3 130733 1 Guard 16 359325 1 Lever 4 359383 1 Key, Pulley Mtg. 17 359326 1 Clip 5 271686 1 Pulley, Crankshaft (5 hp) 18 445768 3 Flange Nut, 1/4” - 20 Hex Cap 6 415562 2 Screw, 5/16” - 18 x 5/16” Socket Head Cap Pt. 19 359321 1 Idler 7 400235 1 Screw, 1/2” x 3/4” Hex Head 20 162069 1 Idler Shaft 8 446145 1 Lock washer, 1/2 Heavy 21 446136 4 Lock washer, 5/16” Heavy 9 162035 1 Belt Guide (Honda 162067) 22 443106 8 Nut, 5/16” - 18 Hex 10 400194 4 Screw, 5/16” x 1 1/2” Hex Cap 23 400112 3 1/4” - 20 x 1 1/4” Hex Head 11 359343 1 Bracket Upper 24 446136 4 Lock washer, 5/16” Heavy 13 336672 1 Pulley 25 443106 1 Nut, 5/16” - Hex 14 359340 1 Bracket Lower 26 400208 4 Screw, 1/4” - 20 x 1 1/4” Hex Drive Assembly Illustration 1 Ref. Part Qty Description Ref. Part Qty Description 1 359328 1 Belt, V-Drive 2 408883 3 Screw, 1/4” - 20 x 1/2” Hex Cap 15 443109 3 Nut 3/8” - NF5 Hex 3 130733 1 Guard 16 359325 1 Lever 4 359383 1 Key, Pulley Mtg. 17 359326 1 Clip 5 271686 1 Pulley, Crankshaft (5 hp) 18 445768 3 Flange Nut, 1/4” - 20 Hex Cap 6 415562 2 Screw, 5/16” - 18 x 5/16” Socket Head Cap Pt. 19 359321 1 Idler 7 400235 1 Screw, 1/2” x 3/4” Hex Head 20 162069 1 Idler Shaft 8 446145 1 Lock washer, 1/2 Heavy 21 446136 4 Lock washer, 5/16” Heavy 9 162035 1 Belt Guide (Honda 162067) 22 443106 8 Nut, 5/16” - 18 Hex 10 400194 4 Screw, 5/16” x 1 1/2” Hex Cap 23 400112 3 1/4” - 20 x 1 1/4” Hex Head 11 359343 1 Bracket Upper 24 446136 4 Lock washer, 5/16” Heavy 13 336672 1 Pulley 25 443106 1 Nut, 5/16” - Hex 14 359340 1 Bracket Lower 26 400208 4 Screw, 1/4” - 20 x 1 1/4” Hex SET UP INSTRUCTIONS CONTINUED TINE ASSEMBLY (Figure 4) Assemble the inner tine assemblies to the transmission. Secure with clevis and hair pins. The short end of the tube goes next to the transmission. Be sure the cutting edge of the blade faces the direction of rotation. Assemble the out tines to the inner tine tubes and secure with hair pins and clevis pins. FINAL SETUP (Figure 5) 1. Remove the oil fill plug from the engine. With the unit sitting level, fill the crankcase with oil. See the engine instruction manual for type and further directions (Figure 5). 2. Fill the gas tank with clean, fresh, regular grade gasoline. Do not mix oil and gas. 3. When cranking the unit, be sure no one is standing in front or near the unit. Check for proper operation of the clutch lever (see page 7). Figure 4 Figure 5 GENERAL INFORMATION The Maxim Chain Drive is the most versatile power unit ever developed for the home gardener and does a soil preparation job second to none, so a few minutes spent in studying the following instructions will pay many dividends. The tiller will dig deeper and move forward slower by pushing down on the handles, and it will go ahead faster but at a shallower depth by raising up on the handles. The speed of the rotors is controlled by the use of the throttle. To control the depth of tilling, the tiller must be operated with both the proper throttle speed and correct up and down hand pressure on the handles. Raising up m...
Эта инструкция также подходит к моделям:Садовые инструменты - MS50B, MS30B, MS50BR (2.09 mb)