Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
This could also pull you off balance. 2 104296 OWNER’S MANUAL SAFETY WARNINGS continued KICKBACK WARNING: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious injury to user. Kickback Safety Devices On This Saw This saw has a low-kickback chain and reduced kickback guide bar. Both items reduce the chance of kickback, however, kickback can still occur with this saw. The following steps will reduce the risk of kickback. • Use both hands - one gripping the handle and the other gripping the pole. Use firm grip. Thumbs and fingers must wrap around pole and handle. • Keep all safety items in place on saw. Make sure they work properly. • Do not overreach or extend arms above shoulder height. • Keep solid footing and balance at all times. • Never try cutting through two branches at the same time. Only cut one at a time. • Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose). • Watch for shifting of wood or other forces that may pinch chain. • Use extreme caution when re-entering a previous cut. • Use low-kickback chain and guide bar supplied with the chain saw. Only use replacement parts listed for the pole saw. • Never use dull or loose chain. Keep chain sharp and adjusted correctly. Saw Maintenance and Kickback Safety Follow maintenance instructions in the chain saw manual. Proper cleaning of saw and chain and guide bar maintenance can reduce chances of kickback. Inspect and maintain saw after each use. This will increase the service life of your saw. Note: Even with proper sharpening, risk of kickback can increase with each sharpening. MAINTENANCE AND STORAGE OF POLE SAW Unplug Pole Saw from power source and follow maintenance and storage procedures outlined in the Maintenance and Storage section of your chain saw manual. POLE SAW TRIMMING PRECAUTIONS Never stand directly under the limb you are trimming. Always position yourself out of the path of falling debris. Never stand on a ladder or other type of unstable support while using the Pole Saw. Always use both hands to operate Pole Saw. Keep a firm, steady pressure on the Pole Saw while cutting but do not try to force the saw through the wood. Do not use the Pole Saw to cut limbs larger in diameter than the length of the guide bar. Keep other persons away from cutting end of polesaw and at a safe distance from work area. Do not use Pole Saw near cable, elec- tric power or telephone lines. Main- tain a minimum clearance of 10 feet from all power lines. 104296 3 ® ® 8’ ELECTRIC TELESCOPING POLE SAW PRODUCT IDENTIFICATION Saw Chain Hand Guard Guide Bar Oil Cap Handle Bracket Power Cord Inner Pole Tighten Coupling Nut Outer Pole Trigger Switch Lock-out Trigger Switch Power Cord Loosen Grip Area Figure 1 - Pole Saw Product Identification POLE SAW NAMES AND TERMS Coupling Nut Threaded collar (loosen to slide inner pole, tighten to hold pole in position). Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Inner Pole The moveable section of tubing to which the saw is attached. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Oiler Control System for oiling guide bar and chain. Outer Pole Retains the moveable inner pole. Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain. Sprocket Toothed wheel that drives chain. Switch Device that completes or interrupts electrical circuit to motor of saw. Switch Lockout Device that reduces accidental starting of saw. Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. 4 104296 104296 5 OWNER’S MANUAL UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought the Pole Saw. ASSEMBLY The plastic hardware bag for the Pole Saw should include the following: CHAIN SAW HARDWARE • (2) Guidebar bolts • (2) Guidebar nuts • (1) Phillips self tapping screw • (1) Saw chain • (1) Guide bar • (1) Hand guard • (1) Scabbard POLE SAW HARDWARE • (1) Handle bracket • (4) #10 x 24 Phillips screws • (4) #10 lockwashers ASSEMBLY OF CHAIN SAW Assemble the chain saw before assembling the pole. R...