Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
3. Remove the lock nut from the middle bolt in the crossover tube and shaft support plate. Leave the bolt in place. See figure 2. 4. Assemble the short end of the hitch tube onto the middle bolt and secure it with the same nut you removed. DO NOT TIGHTEN YET. See figure 2. IMPORTANT: The hitch tube must attach to the side of the crossover tube opposite the shaft support plate. 5. Assemble the two hitch braces to the hitch tube using a 1/4" x 2" hex bolt and a 1/4" nylock nut. DO NOT TIGHTEN YET. See figure 2. FIGURE 3 9. Assemble the short spacer tube and a 1-5/8" flat washer onto the end of the axle that has the large hole. See figure 4. 10. Place the drive wheel (bolt hole through hub) onto the axle so that the air valve is to the outside. Secure the wheel to the axle with a 1/4" x 2" hex bolt and a 1/4" nylock nut. See figure 4. 13. Assemble the hitch bracket to the top of the hitch tube using two 3/8" x 1-1/4" hex bolts and 3/8" nylock nuts. See figure 6. 14. Assemble the hitch pin through the hitch bracket and the hitch tube and secure with the hair cotter pin. See figure 6. 3/8" x 1-1/4" HEX BOLT3/8" LOCKWASHER3/8" NYLOCK NUTHITCH PINHAIR COTTER PIN 1/4" NYLOCK NUT1/4" x 2" HEX BOLTDRIVE WHEELAIR VALVESHORT SPACER TUBE1-5/8" DIA. FLAT WASHER FIGURE 6 FIGURE 4 15. Assemble the flow control link (end with small hole) to the flow control arm using a 1/4" x 1" hex bolt, a nylon washer and a 1/4" nylock nut. Tighten the nut until the flow control link pivots with a slight resistance. See figure 7. 11. Turn the spreader upright on its wheels. 12. Attach the hopper strap to the front and rear of the hopper using two 1/4" x 1" hex bolts, 5/16" flat washers, nylon washers and 1/4" nylock nuts. See figure 5. FLOW CONTROLLINKFLOW CONTROL ARM1/4" NYLOCK NUT1/4" x 1" HEX BOLTSMALLEST HOLENYLONWASHER HOPPER STRAPNYLON WASHER5/16" FLAT WASHER1/4" x 1" HEX BOLT1/4" NYLOCK NUT FIGURE 5 FIGURE 7 19. Hook the free end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 10. 16. Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 1" hex bolt, two nylon washers and a 1/4" nylock nut as shown in figure 8. Tighten the nut until the flow control arm pivots with a slight resistance. 17. Assemble the vinyl grip. See figure 8. 1/4" x 1" HEX BOLT1/4" NYLOCKNUTFLOW CONTROLMOUNTINGBRACKETFLOW CONTROL ARM(2) NYLONWASHERSVINYL GRIP FIGURE 10 20. Assemble the flow control mounting bracket to the hitch tube using two 1/4" x 2" hex bolts, six 5/16" flat washers and two 1/4" hex lock nuts as shown in figure 11. Do not tighten at this time. FIGURE 8 18. Place a 5/16" flat washer onto the end of the flow control rod. Insert the end of the rod through the slot in the flow control mounting bracket and through the hole in the flow control link. Secure with a 3/32" x 3/4" cotter pin. See figure 9. FLOW CONTROLMOUNTING BRACKET1/4" x 2" HEX BOLT1/4" HEXLOCK NUT5/16" FLATWASHER5/16" FLATWASHER FLOWCONTROLRODFLOW CONTROL LINK3/32" COTTERPIN5/16" FLATWASHERSLOT FIGURE 11 FIGURE 9 21. Place the adjustable stop into the "ON" end of the slot in the top of the flow control mounting bracket. Secure with the 1/4" x 3/4" carriage bolt, a nylon washer, a 5/16" flat washer and the nylon wing nut. See figure 12. 22. Position the flow control mounting bracket. (Figure 13). a. Push on flow control arm until it locks in "OFF" position. b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. c. Snug the 1/4" lock nuts just enough to hold flow control mounting bracket in place. d. Set adjustable stop at "5". Pull flow control arm against stop. Verify that closure plate has opened about half way. e. If closure plate does not open half way, it may be closed too far at "OFF". Adjust position of flow control mounting bracket until closure plate will open about half way at "5" and still close when arm is locked in "OFF". Tighten 1/4" lock nuts. 5/16" FLATWASHERNYLONWASHER1/4" x 3/4" CARRIAGE BOLTNYLONWING NUTADJUSTABLESTOP OFFON12346789105FLOWCONTROLARMONOFFAJDUSTABLESTOPSETTING "5" FIGURE 12 FIGURE 13 OPERATION HOW TO USE YOUR SPREADER SETTING THE FLOW CONTROL (Refer to figure 13 on page 7.) 1. Loosen the nylon wing nut, set the adjustable stop to the desired flow rate setting and retighten the wing nut. The higher the setting number, the wider the opening in the bottom of the hopper. 2. Refer to the application chart on page 8 and to the instructions on the fertilizer bag to select the proper flow rate setting. 3. Pull the flow control arm against the adjustable stop for the on position and toward the hopper for the off position. OVERLAPREFER TOCHARTS USING YOUR SPREADER We do not recommend the use of any powdered lawn chemicals, due to difficulty in obtaining a satisfactory or consistent broadcast pattern. 1. Determine approximate square footage of area to be covered and estimate amount of material required. 2. Before filling...
Эта инструкция также подходит к моделям:Садовые инструменты - 175 (945.2 kb)