Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
See figure 10. 1/4" x 5/8" HEX BOLT1/4" HEX LOCK NUT FLOW CONTROL LINK EXTENSION SPRING FLOW CONTROL ROD FLOW CONTROL MOUNTING BRACKET FLOW CONTROL ARM FIGURE 10 19. Place a 5/16" flat washer over the end of flow control rod, and insert end of rod through slot in flow control mount bracket and through the hole in flow control link. Secure with a 3/32" x 3/4" cotter pin. See figure 11. FLOW CONTROL LINK EXTENSION SPRING 3/32" COTTER PIN 5/16" FLAT WASHER FLOW CONTROL ROD FLOW CONTROL MOUNTING BRACKET 20. Hook free end of flow control rod through hole in slide gate bracket located near bottom of hopper. See figure 12. HOPPER SLIDE GATE BRACKET FLOW CONTROL ROD FIGURE 12 21. Assemble flow control mounting bracket and the handle tube (short) to the handle tube (long) using two 1/4" x 1-1/2" hex bolts, two 5/16" flat washers and two 1/4" lock nuts. See figure 13. DO NOT TIGHTEN AT THIS TIME. 22. Place handle grip on each handle tube. See figure 13. HANDLE GRIP 1/4" x 1-1/2" HEX BOLTS 1/4" LOCK NUTS HANDLE TUBE (SHORT) HANDLE TUBE FLOW CONTROL MOUNTING BRACKET 5/16" FLATWASHERS5/16" FLAT WASHERS HANDLE GRIP (LONG) FIGURE 13 FIGURE 11 6 23. Assemble the flow control gage onto the flow control mounting bracket using a 1/4" x 3/4" carriage bolt, a nylon washer and hand knob. See figure 14. 24. Move flow control arm to off position and push flow control mounting bracket toward hopper until closure plate (located in bottom of hopper) is completely closed. Tighten 1/4" hex lock nuts assembled in step 21. See figure 14. HAND KNOB NYLON WASHER FLOW CONTROL GAGE OFF 1/4" x 3/4" CARRIAGE BOLT 1/4" HEX LOCK NUTS FLOW CONTROL MOUNTING BRACKET FIGURE 14 25. Lubricate as instructed in the lubrication section on page 8. OPERATION The application spread pattern should overlap to insure uniform coverage at the edges. The approximate distance between each pass is shown in the application diagram. See figure 15. APPLICATION DIAGRAM OVERLAP 8' to 10' FIGURE 15 FLOW RATE ADJUSTMENT 1. Push forward on the flow control arm to the off position and pull back to the on position. The higher the number on flow rate gauge the larger the opening in the bottom of the hopper. See figure 16. 2. REFER TO THE FLOW RATE CHART AND TO INSTRUCTIONS ON FERTILIZER BAG TO SELECT PROPER FLOW RATE SETTING. 3. Loosen the hand knob to set the flow gauge to the desired flow setting and tighten the hand knob. 4. Always move flow control arm to off position before stopping or turning spreader. 5. The spreader should be moving before you move the flow control arm to the on position. 1234 5 67 8 910 OFF ON FLOW CONTROL ARM FLOW RATE GAUGE HAND KNOB FIGURE 16 8 FLOW RATE CHART MATERIAL TYPE Flow Rate Setting At 3 M.P.H. Light Heavy Fertilizer Granular Pelleted 3 5 5 7 Grass Seed Fine - Blue Grass Coarse - Rye, Fescue 2 4 6 8 Ice Melters Granular Pelleted 6 8 6 8 3 M.P.H. is equivalent to traveling 100 feet in 23 seconds. NOTE Do not use powdered lime, only granulated materials are approved for use. 1. Determine approximate square footage of area to be covered and estimate amount of fertilizer or seed required. 2. With flow control arm in off position, set flow rate gauge at number indicated in flow rate chart for light or heavy application rate. Also, refer to instructions on bag for manufacturers recommended settings. 3. Break up lumpy fertilizer as you fill hopper. 4. To broadcast, always have spreader in motion before opening closure plate. Do not allow spreader to sit stationary with flow control arm in ON position. If fertilizer is accidentally deposited to heavily in small area, soak down thoroughly with garden hose to prevent burning of lawn. IMPORTANT: Application rates (shown on chart) are affected by humidity and mixture content of material (granular and pellet); therefore, minor adjustment settings may be necessary to compensate for this condition. The rate chart is calculated for light and heavy application. The faster you walk, the wider the broadcast width. A variation in speed will determine the flow rates and width of broadcast. ATTENTION: When broadcasting weed control fertilizers, make sure broadcast pattern does not hit evergreen trees, flowers or shrubs. MAINTENANCE & STORAGE 1. Do not store spreader with any material in hopper. 2. Clean your spreader after use. Flush thoroughly with water. 3. If for any reason the axle, gear and sprocket assembly is disassembled, be sure to mark position of parts as they are removed. The positions of the drive wheel and sprocket in relation to the slotted plastic gear determine which direction the spreader plate will spin. Be sure to reassemble them in their original positions. (Refer to figure 5 on page 4.) With the reassembly of the gear and sprocket, use shim washers (Ref. no. 21 on page 10) as needed for minimum backlash. Add grease to gear and sprocket. 4. If agitator wire becomes damaged or worn it can be replaced. Loosen 3/8" lock nut on the top of sprocket shaft until agitator wire is free. Remove old ...