Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
CONTACT YOUR LOCAL AUTHORIZED TRACTOR DEALER FOR MORE INFORMATION. PRECAUCION: SE REQUIERE QUE INSTALE UN KIT DE CONTRAPESO FRONTAL EN SU CORTACESPED ANTES DE USAR ESTE PRODUCTO. PARA OBTENER MAS INFORMACION, COMUNIQUESE CON EL DISTRIBUIDOR AUTORIZADO DE TRACTORES. ATTENTION: IL EST OBLIGATOIRE D'INSTALLER UN KIT DE MASSES D’ALOURDISSEMENT SUR LA TONDEUSE AVANT D’UTILISER CET ARTICLE. CONTACTEZ VOTRE CONCESSIONNAIRE DE TRACTEURS DE VOTRE REGION POUR PLUS D’INFORMATION. FORM NO. 40977 (08/25/08) PRINTED IN U.S.A. 2 RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. Read this owners manual before attempting to • assemble or operate the spreader. Read the vehicle owners manual and know how • to operate your vehicle before using the spreader attachment. Do not allow anyone to ride on or sit on spreader • attachment frame. Never allow children to operate the vehicle or • spreader attachment. Do not allow adults to operate the vehicle or spreader • attachment without proper instructions. Never operate vehicle and spreader attachment • without wearing solid, substantial footwear. Wear eye and hand protection when handling and • using lawn chemicals. Always begin with the transmission in first (low) and • gradually increase speed as conditions permit. When using broadcast spreader do not drive too • close to a creek or ditch and be alert for holes and other hazards which could cause you to lose control of the broadcast spreader and vehicle. Always operate vehicle and spreader up and down a • slope, never across a slope. Read instructions and caution notes for handling and • application of materials purchased for spreading. Follow maintenance and lubrication instructions as • outlined in this manual. Always use front weight kit on tractor when using • spreader. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CARTON CONTENTS Hopper/Frame Assembly1. Control Mount Tube2. Vinyl Cover3. Impeller4. Motor Mount Assembly5. Impeller Shaft6. Wire Harness7. Deflector8. Screen9. 165483927 SHOWN FULL SIZE A B C GJ KIEDHNOLM F NOT SHOWN FULL SIZE KEY QTY. DESCRIPTION A 4 Hex Bolt, 5/16 x 2" B 6 Hex Bolt, 5/16 x 1" C 2 Hex Bolt, 1/4 x 3/4" D 4 Nylock Nut, 1/4" E 8 Nylock Nut, 5/16" F 4 Nylon Washer G 2 Flat Washer, 1/4" H 4 Flat Washer, 5/16" KEY QTY. DESCRIPTION I 4 Spacer, .31 x .56 x .36" J 3 Cotter Pin, 1/8 x 1-1/4" K 1 Agitator Hairpin L 1 Coupler M 2 Seal N 3 Nylon Tie O 2 Angle Bracket ASSEMBLY INSTRUCTIONS Insert agitator hairpin into middle hole in the spreader 4. shaft. Assemble a seal (turned as shown in figure 3) onto end of the spreader shaft closest to hairpin agitator. See figure 3. Slide end of spreader shaft having the seal through the 5. plastic bushing in the bottom of hopper. See figure 3. Slide the impeller onto the spreader shaft and secure 6. it with a 1/8" x 1-1/4" cotter pin. See figure 3. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (2) 7/16" Wrenches (2) 1/2" Wrenches CAUTION: PARTS OF TRACTOR MAY BE HOT! MAKE SURE ENGINE AND MUFFLER ARE COOL BEFORE INSTALLING SPREADER! IMPELLER1/8" x 1-1/4" COTTER PINAGITATORHAIRPIN SEALSPREADER SHAFT Turn the spreader upside down as shown in figure 1.1. Assemble two angle brackets and two 1/4" nylock nuts 2. onto the ends of the longer bolts already assembled to the frame tube. Do not tighten yet. See figure 1. ANGLEBRACKET1/4" NYLOCK NUT FIGURE 3 FIGURE 1 Fasten deflector to angle brackets using two 1/4" x 3. 3/4" hex bolts, 1/4" flat washers and 1/4" nylock nuts. Allow angle brackets to swivel so deflector curves naturally between angle brackets and then tighten all nuts. See figure 2. Assemble a seal (turned as shown in figure 4) onto 7. the motor shaft. Slide it up against the motor. Assemble the impeller coupler onto the motor shaft 8. and secure it with a 1/8" x 1-1/4" cotter pin. Spread the ends of the pin around the coupler. See figure 4. 1/4" FLATWASHERDEFLECTOR1/4" x 3/4" HEX BOLT1/4" NYLOCK NUT 1/8" x 1-1/4" COTTER PINSEALIMPELLERCOUPLER FIGURE 4 FIGURE 2 Attach the control mount tube to the top of the 14. spreader using a 5/16 x 1" hex bolt and 5/16" nylock nut. See figure 7. NOTE: The end of the control mount tube with the smaller bend should be attached to the spreader. Place screen down into hopper. 9. DO NOT place it under the clips in bottom of hopper at this time. See figure 6. Place motor assembly down into hopper, inserting end of 10. spreader shaft into impeller coupler. Secure it with a 1/8" x 1-1/4" cotter pin, spreading ends of pin around coupler. See figure 5. Fasten motor mount bracket to hopper using four 5/16" x 11. 1" hex bolts, 5/16" flat washers, nylon washers and 5/16" nylock nuts. See figure 5. 5/16" x 1" HEX BOLT5/16" NYLOCK NUT 5/16" x 1" HEX BOLTNYLONWASHER5/16" NYLOCK NUTMOTORASSEMBLY5/16" FLAT WASHERSCREEN1/8"...