Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Refer to the Application Chart on this page and to the instructions on the fertilizer bag to select the proper flow rate setting. 3. Move the flow control arm past the adjustable stop to the “OFF” position so that the closure plate is shut. 4. Fill the hopper, breaking up any lumpy fertilizer. 5. The Application Chart is calculated for light-to-heavy application at a walking speed of 3 mph, or 100 ft. in 23 seconds. A variation in speed will require an adjustment of the flow rate to maintain the same coverage. The faster you travel, the wider the broadcast width. 6. Always start the spreader in motion before opening the closure plate. 7. Always shut the closure plate before turning or stopping the spreader. 8. If fertilizer is accidentally deposited too heavily in a small area, soak the area thoroughly with a garden hose or sprinkler to prevent burning of the lawn. 9. To insure uniform coverage, make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass as shown in figure 19. The approximate broadcast widths for different materials are shown in the Application Diagram figure 19. 10. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. IMPORTANT: Application rates shown in the chart are affected by humidity and by the moisture content of the material (granular and pellet). Some minor setting adjustments may be necessary to compensate for this condition. APPLICATION CHART MATERIAL TYPE FLOW SETTING 3 MPH (100 FT. IN 23 SEC.) SPREAD WIDTH IN FEET FERTILIZER Powder Granular Pelleted Organic GRASS SEED Fine Coarse ICE MELTER 3-5 3-5 3-5 6-8 3-4 4-5 6-8 3-4 8-10 10-12 6-8 6-7 8-9 10-12 OPERATING SPEED - 3 MPH. (100 ft. in 23 seconds) OVERLAPREFER TOCHARTS FIGURE 19 MAINTENANCE CHECK FOR LOOSE FASTENERS 1. Before each use, make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. CHECK FOR WORN OR DAMAGED PARTS 2. Check for worn or damaged parts before each use. Repair or replace parts if necessary. CHECK TIRE INFLATION 3. Check if tires are adequately inflated before each use. Do not inflate tires beyond maximum recommended pressure. CLEANING 4. Rinse inside of hopper and exterior of spreader and allow to dry before storing. LUBRICATE (See figure 20) 5. Remove one small and two large hairpins and separate the gearbox housings. 6. Lightly apply automotive grease as needed to the gears. 7. Oil the nylon bushings on the vertical sprocket shaft. Apply grease to the axle at least once a year, or more often as needed. 8. Oil (idler) wheel at least once a year or more often as needed. 9. Install gearbox housings and secure with hairpins. OILGREASEHAIRPINHAIRPIN FIGURE 20 CAUTION: DO NOT inflate tires beyond the maximum recommended pressure printed on side of tire. STORAGE 1. Rinse inside of hopper and exterior of spreader and allow to dry before storing. 2. Store in a clean, dry area. SERVICE AND ADJUSTMENTS 1. If the axle and gear assembly is disassembled, mark down the positions of the parts as they are removed. The large gear position in relation to the small gear determines which direction the spreader plate will spin. Be sure to reassemble them in their original positions. (Refer to parts exploded view on page 10). Ensure washer (Refer to item 33 on page 10 and 11) is in place when assembling the axle components. Add grease to gears. 2. If the agitator hairpin becomes damaged or worn, it can be replaced. Remove old agitator hairpin from hole in impeller shaft and replace with new agitator hairpin. See figure 21. SPROCKETSHAFTAGITATORHAIRPIN FIGURE 21 REPAIR PARTS FOR BROADCAST SPREADER MODELS 45-0414, 45-0415 1 43 34 45 54 33 55 41 38 52 8 42 66 53 45 52 45 65 8 61 39 5 8 52 62 33 35 33 9 8 8 8 45 8 8 29 25 29 30 26 33 31 31 22 32 27 62 57 33 33 36 33 4 4 3 45 56 56 8 8 8 47 60 44 50 58 48 49 59 51 44 60 9 47 8 9 25 28 31 37 20 21 1513 19 18 15 8 17 10 40 46 12 67 3 2 8 11 24 23 64 9 9 6 7 5 5 9 6 5 19 63 8 68 REPAIR PARTS FOR BROADCAST SPREADER MODELS 45-0414, 45-0415 REF. PART NO. QTY DESCRIPTION 1 44466 1 Hopper, Spreader (125 lb.) 2 48842 1 Tube, Frame (45-0414) 48842SS 1 Tube, Frame (45-0415) 3 25755 2 Handle, Lower (45-0414) 25755SS 2 Handle Lower (45-0415) 4 741-0249 4 Bearing, Flanged 5 1543-69 8 Washer, Nylon 6 49890 4 Washer, 1/4" * 7 25672 2 Clip 8 49891 27 Nylock Nut, 1/4-20 * 9 49892 11 Hex Bolt, 1/4-20 x 1-3/4" * 10 65457 1 Closure Guide 11 25757 1 Plate, Pattern 12 23533 1 Plate, Closure 13 44285 1 Bushing, Hopper Bottom 15 41157 6 Pop Rivet, 3/16" Stainless Steel 17 25758 1 Link, Flow Control 18 25917 1 Slide Gate Angle Bracket 19 40199 2 Hex Bolt, 1/4-20 x 3/4" * 20 04367 1 Spreader Impeller 21 49896 1 Shaft, Impeller 22 26027 1 Axle 23 49910 2 Spacer, Axle Tube 24 49798 2 Fitting, Grease 1/4" 25 47212 2 Housing, Large Gear 26 47204 1 Yoke, Large 27 47209 1 Gear, Large 28 47205 1 Gear, Small 29 49897 2 Clip, Hairpin 7/8...
Эта инструкция также подходит к моделям:Садовые инструменты - 45-0414 (2.38 mb)