Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
CHECK OR FILL ENGINE CRANKCASE Important: Engine is shipped from factory without oil. You must add engine oil before starting engine. 1. Add oil according to engine manual. Do not overfill. Use a clean, high quality detergent oil. Do not mix oil with gasoline. Oil level must be full. check the oil level by removing oil fill plug. 2. Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use. CHECK TILLER TRANSMISSION OIL Important: Tiller transmission is shipped from factory with the proper amount of oil. When replacing oil, the tiller transmission holds 18-22ounces. Do not overfill. Check the oil level annually. To check the oil level: 1. Move tiller to level ground. 2. Remove oil level dipstick located between the handlebar mounts on the engine mount. If the oil level couldn’t touch the dipstick, fill the oil to recommended level. 3. Replace oil level dipstick in the filler hole. 4. Note that the drive wheel transmission and rear tine transmission are one common reservoir. When you add to the front transmission, you must wait a short period of time for the oil to flow rearward and equalize in both front and rear. The dipstick will read correctly on level ground for both gear units. CHECK TIRE PRESSURE Recommended tire pressure is 30 PSI. If tires do not have equal pressure, tiller will pull to one side. LUBRICATION Proper lubrication of moving mechanical parts is critical for proper care and maintenance. Oil the moving parts shown at 10 hour intervals using a 30 weight oil. CLEAN TINE AXLE SHAFT 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire and secure from spark plug. 3. Tip the tiller forward. Block the tiller in position so that it rests on the engine mount and the tines are exposed. 4. Remove all vegetation, string, wire, and other material that may have accumulated on the axle between the inside set of tines and the seal cover on the transmission housing. 5. Tip the tiller back to a level position. 6. Replace spark plug wire. Gear Case Dipstick Transmission Cover Plate Figure 14 Questions? Call Toll Free at 1-800-737-2112 18 Copyright © 2009 MAT Engine Technologies, LLC Maintenance (Continued) • Save all instructions How to Prepare for Storage D WARNING Never store the tiller indoors with fuel in the fuel tank. Never store in an enclosed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, water heater or clothes dryer. Allow engine to cool before storing unit. WARNING Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline fumes can cause an explosionor a fire. NOTE: A yearly checkup or tune-up at an authorized service center will make sure that the tiller will provide maximum performance for the next season. When the tiller is put in storage for thirty days or more, the following steps should be followed to make sure the tiller is in good condition the next season. 1. Let the engine run until it is out of gasoline. 2. Change the oil by following instructions under “How to Change the Oil.” 3. Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil-start grip so that the oil will protect the cylinder. Install a new spark plug in the cylinder. Pull starter handle slowly a few times todistribute oil. Pull recoil slowly until resistance is felt. This will close the cylinder valves. WARNING DO NOT attach spark plug wire to spark plug when storing unit. 4. Clean tiller. Remove all dirt, leaves, debris, grease, etc. from the tiller - including cylinder cooling fans, recoil starter cover holes, under fuel tank, and under muffler. 5. Check the tiller for worn or damaged parts. Have damaged parts replaced if necessary. 6. Tighten any loose hardware. 7. Apply lubrication as directed in Maintenance section. 8. Put the unit in a building that has good ventilation. 9. Cover the tiller with a breathing material. Technical Service You may have further questions about assembling, operating, or maintaining this TILLER. If so, you can contact our Technical Service Department at 1-800-737-2112 (English only). You may also write to: METL Corporate Office - CORRESPONDENCE ONLY ATTN: Technical Service – METL 6700 Wildlife Way If you need assistance or have any questions, CALL TOLL FREE: 1-800-737-2112. Long Grove, IL 60047 When contacting the Technical Service Department, have ready: • Your Name • Model Number of Product • Your Address • Your Phone Number • Date of Purchase (include copy of receipt for written requests) Questions? Call Toll Free at 1-800-737-2112 19 Copyright © 2009 MAT Engine Technologies, LLC Maintenance (Continued) • Save all instructions PROBLEM POSSIBLE CAUSE(S) SOLUTION(S) Engine difficult to start 1. Out of fuel 1. Add fresh fuel 2. Engine Switch Off2. Turn engine switch on3. Engine is not primed. 3. Turn choke on 4. Attach spark plug wire to spark plug4. Spark plug wire disconnected5. Remove spark p...
Эта инструкция также подходит к моделям:Садовые инструменты - P-RTT-196MD-[E] (907.59 kb)