Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
S Allow engine to cool and secure unit before storing or transporting it in a vehicle. S Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the engine and letting it run until it stops. S Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Store unit so the blade cannot accidentally cause injury. S Store unit indoors, out of reach of children. SPECIAL NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. SAVE THESE INSTRUCTIONS 3 4 ASSEMBLY WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts. NOTE: If you need assistance or find that parts are missing or damaged, call 1-800-554-6723. TOOLS REQUIRED S Hex wrench (provided) HANDLEBAR ASSEMBLY DANGER:RISK OFCUT. To avoid serious injury, the barrier portion of the handlebar must be installed as shown on the upper tube of the powerhead to provide a barrier between operator and the spinning blade. Attach tube clamp above arrow on safety warning decal on the upper tube (powerhead end of unit). Ensure handlebar is positioned on handlebar clamp between the arrows on the handlebar decal. NOTE: The tube clamp base has four spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1" diameter upper tube (the tube clamp will not tighten down securely on the 1" diameter upper tube without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the clamp base. These tabs are not needed for powerheads with a 7/8" upper tube. Spacer Tabs HANDLEBAR CLAMP BASE Spacer Tabs positioned for use on 1" diameter upper tube 1. Place the tube clamp over the upper tube above the arrow on the safety decal. 2. Position the clamp base under the upper tube and align the tube clamp and clamp base screw holes (use spacer tabs between tube clamp and clamp base if necessary to secure clamp, i.e. for 1" diameter upper tube). POWERHEAD END ATTACHMENT END Screws Clamp Base Handlebar Clamp between arrows on handlebar decal Clamp Knob Tube Clamp Handlebar Arrow on Safety Decal 3. Insert four screws into the screw holes. 4. Secure tube clamp by tightening screws with the hex wrench. 5. Position the handlebar as shown, ensuring the handlebar is positioned on the handlebar clamp between the two arrows on the handlebar decal. 6. Retighten handlebar by turning clamp knob clockwise until handlebar is secure and stationary in clamp (clamp knob cannot be overtightened). SHOULDER STRAP ASSEMBLY WARNING: Proper shoulder strap and handlebar adjustments are required before use. The shoulder strap clamp must be installed as shown above the handlebar on the upper tube (powerhead end of unit). NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1" diameter upper tube (the shoulder strap clamp will not tighten down securely on the 1" diameter upper tube without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8" upper tube. 5 Spacer Tabs LOWER SHOULDER STRAP CLAMP Spacer Tabs positioned for use on 1" diameter upper tube 1. Place the upper shoulder strap clamp over the upper tube above the handlebar. 2. Position the lower shoulder strap clamp under the upper tube and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i.e. for 1" diameter upper tube). Upper Shoulder Strap Clamp Screws Lower Shoulder Strap Clamp POWERHEAD END ATTACHMENT END 3. Insert two screws into the screw holes. 4. Secure shoulder strap clamp by tightening screws with the hex wrench. 5. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. 6. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your wai...
Эта инструкция также подходит к моделям:Садовые инструменты - 530086792 (292.45 kb)