Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Correct height Adjust the shoulder strap so that the cutting attachment is parallel to the ground. Correct balance Let the cutting attachment rest lightly on the ground. Adjust the position of the suspension ring to balance the clearing saw correctly. Fuel safety Never start the machine: 1If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water. 3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines. Transport and storage •Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers. •When storing and transporting fuel always use approved containers intended for this purpose. •When storing the machine for long periods the fuel tank must be emptied. Contact your local petrol station to find out where to dispose of excess fuel. •Ensure the machine is cleaned and that a complete service is carried out before long-term storage. •The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. •Secure the machine during transport. WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes. Fuel NB! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. WARNING! Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation. Petrol NB! Always use a quality petrol/oil mixture at least 90 octane (RON). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded petrol/oil mixture. Leaded petrol will destroy the catalytic converter. Use low-emission petrol, also known as alkylate petrol, if it is available. •The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage. •When working at continuous high revs a higher octane rating is recommended. Two-stroke oil •For best results and performance use JONSERED two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. •Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). •Never use oil intended for four-stroke engines. •A poor oil quality and/or too high oil/fuel ratio may jeopardise function and decrease the life time of catalytic converters. •Mixing ratio 1:50 (2%) with JONSERED two-stroke oil. 1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines. Petrol, litre Two-stroke oil, litre 2% (1:50) 3% (1:33) 5 0,10 0,15 10 0,20 0,30 15 0,30 0,45 20 0,40 0,60 Mixing •Always mix the petrol and oil in a clean container intended for fuel. •Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. •Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. •Do not mix more than one month’s supply of fuel at a time. •If the machine is not used for some time the fuel tank should be emptied and cleaned. WARNING! The catalytic converter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/or vapours. Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refuelling. Always move the machine away from the refuelling area before starting. •Always use a fuel container with an anti-spill valve. •Clean the area around the fuel cap. Contamination in the tank can cause operating problems. •Ensure that the fuel is well mixed by shaking the container before filling the tank. Check before starting •Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been for...
Эта инструкция также подходит к моделям:Садовые инструменты - BC2053 (1.86 mb)