Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.) • Tighten the nut using the socket spanner. 35-50 Nm (3.55 kpm). The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times. Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting performance. • Extend the life of cutting equipment. IMPORTANT! Only use cutting attachments with the guards we recommend! See the chapter on Technical data. Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter. ! WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it. ! WARNING! A faulty cutting attachment may increase the risk of accidents. Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords.These have been tested by the manufacturer to suit a particular engine size.This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data. • Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared. • The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.This will make the line tougher so that it lasts longer. English – 9 ASSEMBLY Fitting the loop handle (326C) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (326L, 326Lx, 326LDx) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • 326L: Fit the nut, washer and screw. 326LX/326LDX: Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft (326LDx) Assembly: • Make sure the knob is loose. • Align the cut-out in the lower part of the shaft with the coupling locking tab on the upper part of the shaft. Then lock the sections together. • Tighten the knob. Dismantling: • Undo the knob (at least three turns). • Push the knob towards the coupling. • Carefully twist the lower half of the shaft to unlock it. • Hold both parts of the shaft and pull the lower part of the shaft out of the coupling. 10 – English ASSEMBLY Fitting the trimmer head ! WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury. ! Fitting a trimmer guard and Superauto II 1" trimmer head (326L, 326Lx, 326LDx) G F I A B C K J I KL • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows: • Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Pull apart the trimmer head, grasping the cover firmly. • Place the cover (I) and the support flange (F) on the output ...