Оценок - 6, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Use a 5,5 mm round file with a file holder. • The sharpening angle is 15°. Every other tooth is sharpened to the right and the intermediate tooth to the left. When the blade has been heavily pitted by stones the upper side of the teeth can, in exceptional cases, need to be dressed using a flat file. In such cases this takes place before sharpening with the round file. Dressing the top side must be carried out equally for all teeth. • Adjust the setting. This should be 1 mm. Sharpening the grass blade • See the cutting equipment’s packaging for correct filing instructions. • The blades are sharpened using a single cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer head • Only use a trimmer head and trimmer cord that is recommended. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the cutting equipment we recommend! See chapter “Technical data“. • Generally smaller machines require a small trimmer head and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and also meet resistance from the grass being cleared. • The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. • Make sure the knife positioned on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a few days. This will make the line tougher and it will keep longer. IMPORTANT INFORMATION Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise harmful vibrations will occur. ! WARNING! Always stop the engine before starting work on any part of the cutting equipment. This continues to rotate even after the throttle has been released. Ensure that the cutting equipment has stopped completely and remove the cable from the spark plug before you start to work on it. 10 – English SAFETY INSTRUCTIONS General safety instructions IMPORTANT INFORMATION • This machine is intended solely for trimming and clearing grass and for light brush-cutting. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“. • Never use the machine if you are tired, if you have consumed alcohol, or if you are taking medicines that can affect your sight, your judgement or the control of your body. • Use personal protective equipment. See the section “Personal protective equipment“. • Never use a machine that has been modified so that it no longer corresponds with the original design. • Never use a machine that is faulty. Follow the maintenance, control and service instructions in this Operator‘s Manual. Some maintenance and service actions should be carried out by trained and qualified specialists. See the chapter “Maintenance“. • All covers and guards must be fitted before starting the machine. Check that the spark plug cap and HT lead are not damaged, otherwise you could get an electric shock. • The machine operator shall ensure, while working, that no persons or animals come closer than 15 metres (50 feet). When several operators are working in the same area the safety distance should be at least double tree length, however, at least 15 metres (50 feet). WARNING! Faulty cutting equipment or an incorrectly sharpened blade increases the risk of accidents. ! Start WARNING! ! When the engine starts with the choke lever in the choke or starter throttle position the cutting equipment starts to rotate immediately. • The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loose and cause personal injury. • Never start the machine indoors. Bear in mind the dangers of inhaling the engine‘s exhaust fumes. • Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment. • Place the machine on the ground, ensure the cutting equipment runs free of twigs and stones. Push the machine body towards the ground using your left hand. (NOTE! Not with your foot). Grip the starter handle with your right hand and pull the starter cord. Fuel safety • Always use a fuel container with an anti-spill valve. • Never fill the machine while the engine is running. Always stop the engine and let it cool for a few minutes before refuelling. • Provide good ventilation when filling or mixing fuel (petrol and 2-stroke oil). • Move the machine at least 3 m from the filling position before starting. • Never start the machine: a)If you have spilt fuel on it. Wipe up all spillage. b)If you have spilt fuel on yourself or your clothes. Change your clothes. c)If there is a fuel leak. Make regular checks for leakage from the fuel cap and the fuel supply pipes. Min. 3 m (10 ft) Transport and storage • Store and transport ...