Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Lock the blade in place by centering the safety clip on the output shaft. CAUTION! Install the blade so its printed surface is visible to the operator when the brushcutter is in the normal operating position. WARNING! ...................................................................................................................................... hole must be centered over the raised boss on blade Holder A. WARNING! ............................................................ the blade and the splines engaged to the output shaft. Install blade holder B on the output shaft.5. The recess in the holder must completely cover the safety clip, and must fit tightly against the blade. Install the bolt guard and then the blade 6. retaining bolt. Using the combination spark plug wrench/screwdriver, tighten the bolt firmly in a counter-clockwise direction. Remove the hex wrench. 7. WARNING! Do not attach any blade to a unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to .................................................................................. and/or bystanders. The unit should now be completely assembled and ready for use with a blade. IMPORTANT! Slide the safety clip off-center Slip the Saw BladeIn Place Slide the Safety ClipBack Shaft Bolt Bolt Guard Holder B Gear shaft Holder A Blade Hex WrenchBlade Holder B Tighten the assembly (blade not shown forclarity) Safety Clip Safety Clip Output Shaft Output Shaft Hex Wrench Discard blades that are bent, warped, cracked, broken or damaged in any way. Use a sharp blade. A dull blade is more likely to snag and thrust. Mixing fuel Examples of 50:1 mixing quantities CAUTION Never use any type of gasoline containing more than 10% alcohol by volume! Some types of gasoline contain alcohol as an oxygenate. Oxygenated gasoline may cause increased operating temperatures. Under certain conditions, alcohol-based gasoline may also reduce the lubricating qualities of some 2-cycle mixing oils. Generic oils and some outboard oils should never be used in your Shindaiwa engine. Filling the fuel tank WARNING! Minimize the Risk of Fire Y NEVER.......................................................... engine. Y ALWAYS stop the engine and allow it to cool before refueling. Y ALWAYS Wipe all spilled fuel and move at least 3 meters (10 feet) from the fueling point and source before starting. Y NEVER................................................ .................................................... Y NEVER operate the engine with .................................................................. screen in place and in good work ing condition. CAUTION This engine is designed to operate on a 50:1 mixture consisting of unleaded gasoline and ISO-L-EGD or JASO FD class 2-cycle mixing oil only. Use of non-approved mixing oils can lead to excessive carbon deposits. Y Use only fresh, clean unleaded gasoline with a pump octane of 87 or higher. Y Mix all fuel with a 2-cycle air-cooled mixing oil that meets or exceeds ISO-LEGD and/or JASO FD classified oils at 50:1 gasoline/oil ratio. CAUTION! Mix and pour fuel outdoors where there .............................................. Y FUEL IS HIGHLY FLAMMABLE. Y ALWAYS store gasoline in a con ........................................................ liquids. Y ALWAYS inspect the unit for fuel leaks before each use. During each ........................................................................ around the fuel cap and/or fuel tank. If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit. Y ALWAYS move the unit at least 3 meters (10 feet) away from a fuel ..................................................................mable materials before starting the engine. U.S. METRIC Gasoline 2-cycle mixing oil Gasoline 2-cycle mixing oil US Gallons Fl.oz. Liter cc. 1 2.6 4 80 2 5.2 8 160 5 13 20 400 10 25.6 30 600 20 51.2 50 1000 50 128 100 2000 IMPORTANT! Mix only enough fuel for your immediate needs! If fuel must be stored longer than 30 days and oil with fuel stabilizer is not used, it should first be treated with a fuel stabilizer such as STA-BIL™. Oil is a registered JASO FD classified oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions engines. Shindaiwa One also includes a fuel stabilizer. 1. Place the unit on a flat, level surface. 2. Clear any dirt or other debris from around the fuel filler cap. CAUTION! Slowly remove the fuel cap only after stopping the engine 3. Remove the fuel cap, and fill the tank with clean, fresh fuel. 4. Reinstall the fuel filler cap and tighten firmly. 5. Wipe away any spilled fuel before starting engine. Starting the Engine IMPORTANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP. WARNING! Never start the engine from the operating posi...
Эта инструкция также подходит к моделям:Садовые инструменты - 89304 (1.76 mb)
Садовые инструменты - 89304 (1.76 mb)
Садовые инструменты - 89304 (1.76 mb)
Садовые инструменты - 89304 (1.76 mb)