Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
ATTACHING THE PLANER TO A VACUUM See Figure 3. The chip collection system of the hand planer has a 1-1/4 in. port for inserting a vacuum hose. . Remove the dust bag. . Attach a vacuum hose to the chip exhaust. . Connect the vacuum to a power supply. WARNING: When the tool is not connected to a vacuum, always reinstall the dust bag back onto the tool. Failure to do so could cause dust or foreign objects to be thrown into your face or eyes, which could result in possible serious injury. 11 WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: . Planing the surface of a piece of lumber . Planing the edge of a piece of lumber . Making rabbet cuts in a piece of lumber CAUTION: If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest service center for service or replacement. CAUTION: Charge in a well ventilated area. Do not block charger vents. Keep them clear to allow proper ventilation. NOTE: Charge only RIDGID lithium-ion batteries on the RIDGID lithium-ion charger and RIDGID nickel-cadmium batteries on RIDGID nickel-cadmium chargers. These batteries and chargers are not interchangeable. Refer to the General Safety Rules for compatibility. THE FOLLOWING INSTRUCTIONS ARE FOR RIDGID 24V LITHIUM-ION BATTERY PACKS AND THE 24V RIDGID LITHIUM-ION CHARGER. CHARGING THE BATTERY PACK NOTE: New 24 Volt lithium-ion battery packs will not work without first being charged. Before first time use, charge the battery pack to activate it. It is not necessary to drain the battery pack completely before recharging. Lithium-ion battery packs have no “memory” and can be recharged at any time. It is therefore possible to charge the battery pack before extended usage even if the battery pack is not completely drained of charge. Use the charge level indicator to determine the amount of charge in the battery pack. Lithium-ion batteries deliver fade free power for their entire run time. 24 Volt lithium-ion tools will not gradually lose power due to decreasing battery charge. Instead, power from the battery pack will drop from full to zero once the full charge has been drained from the battery. Once this happens, the tool’s power drops from full to zero, and recharging of the battery is required OPERATION Fig. 4 CHARGE LEVEL INDICATOR 24vXLi ? OPERATION TO CHARGE A fully discharged battery pack with a temperature between 32°F (0°C) and 150°F (65°C) will charge in about an hour. . Charge the 24 Volt lithium-ion battery pack only with the charger provided. • Connect the charger to a power supply. NOTE: If needed, the charger can operate with most generators and inverters rated at 300 Watts or higher. • Attach the battery pack to the charger by aligning the raised ribs on the battery pack with the grooves in the charger, then slide the battery pack onto the charger. See Figure 4. • Do not place the charger in an area of extreme heat or cold. It will work best at normal room temperature. • After charging is complete, the continuous green light will come on and the charge level indicator lights on the battery will go off. • The charger will keep the battery pack fully charged if left on the charger. CHARGE LEVEL INDICATOR See Figure 5. The charge level indicator shows that the battery is charged at 1/4, 1/2, 3/4, or full capacity. To display the amount of charge left in the battery, press and hold the charge level indicator button. NOTE: When the battery pack contains less than 10% charge, the 1/4 charge level indicator will flash. CHARGING A HOT BATTERY PACK If the battery pack is above normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery pack cools down to approximately 150°F (65°C), the charger will automatically begin fast charge mode. NOTE: Refer to CHARGING THE BATTERY PACK for normal recharging of batteries. If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check. For the location of your nearest repair center, please call 1-866-539-1710. CHARGING A COOL BATTERY PACK If the battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 14°F (-10°C), the charger wi...