Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Round workpieces or workpieces which do not fully rest on the planing/thicknessing bed, or can not be positively held by the thicknesser's recoil lock (e.g. battens with a triangular crossection) can not be worked on these machines. *Derived timber products are materials containing a minimum of 90% wood particles. Transportation To remove the machine from the pallets and for transportation 4 lifting eyes are provided. Place a tube or batten through the eyes to maneuver the machine. After installation of the machine the lifting eyes should be removed. Do not lift machine on the planing bedes. 7 Installation/Initial Operation 7.1 Final Assembly For shipping the fence is not installed and the switch terminal is mounted in a horizontal position. Loosen the screws of the stay brackets, put switch terminal in the vertical position and tighten screws again. A Loosen ratchet lever (a) and slide fence carrier into bracket. 7.2 7.3 7.4 7.5 7.6 8 Installation The machine must be installed on a firm and level floor. Adjust feet until planing beds are level. All four feet must evenly rest on the floor to prevent rocking. Connection to Power Mains -Check if voltage of power mains matches with voltage stated on machine’s type plate (400 V 50 Hz ±5%). -This machine must be operated on a residual current device (RCD) of 30 mA capacity , having a fault current breaker. -The outlet this machine is connected to must be earthed and each phase protected by a 16 A time-lag fuse or circuit breaker. A minimum conductor crossection of 2.5 mm2 is required. -This machine must be safety earthed. The yellow/green lead is the earth conductor. If a plug matching your local standard outlet is fitted to the power cable, do not connect the earth lead to one of the current conducting leads. -Do not operate this machine with a damaged power cable. Risk of electrical shock. -Worn or defective cables must be replaced immediately. Have replaced by a qualified electrician only. Direction of Rotation Important! The direction of rotation of the cutterblock must be against the feed direction. It is factory set on single-phase machines. On machines equipped with a three-phase motor, start machine briefly to check direction of rotation. To change, turn phase inverter pins in plug by 180° with screwdriver. Dust Collection If this machine is operated indoors for more than 30 minutes a day it must be connected to a dust collector (the dust of oak and beech is classified as cancer causing). The dust collector this machine is connected to must provide for a minimum air flow rate of 16 mtr/sec. The dust collection port of the dust chute has a nominal diameter of 100 mm. Automatic Dust Collector Starting The electrical connection of this machine must ensure that a dust collector connected to it automatically starts when the machine is switched on, and provide for 20 sec post-running of the dust collector after the machine is switched off. Safety -Adhere to the instructions, the safety rules in particular. -Disconnect from power (pull plug form outlet) before servicing. -Check guards daily as per para. 14 of this manual. -Never reach into feed openings while machine is running. Observe warning label with crossed-out hand on machine, indicating the danger (see also above). -Follow instructions for fence and guard setting (para. 12.4 and 12.6). -Do not use planer blades of less than 22 mm width. -Dust collection as per para. 7.5 of this manual must be provided for. -Do not work stock larger than the max. workpiece dimensions as per para. 9. -Never operate machine without cutterblock guard in place. -Replace damaged parts and safety guards at once with genuine metabo parts. -Person under the age of 16 are not permitted to operate this machine. -In case of disturbances always let the cutterblock come to a complete standstill before checking the machine. -Always have guard and fence set for the job on hand. -Always wear snug fitting clothes and take off rings, bracelets and watches before operating this machine. -While this machine is in operation the cutterblock must be completely covered, by fence, cutterblock guard, and workpiece. -Wear hearing protection for all jointing and planing operations (warning symbol shown above). The sound pressure level can rech up to 87 dB(A). -Check stock before working it for cracks, intergrown knots, warps and inclusion of foreign material. -Do not exceed maximum permissible torque when tightening lock bar screws (see para. 15). -When operated with wheel set installed support machine with all four levelling screws to keep it from tipping. 9. Workpiece Dimensions 9.1 HC 410 Planing/Jointing The max. permissible workpiece size is 1700 x 410 mm when using the standard machine tables. If workpieces of greater length are to be worked additional support is required, e.g. by using roller stands. The smallest size for manual feeding by hand must not be less than 300 X 40 X 20 mm. Smaller workpieces must be fed with a suitable push block....