Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Adjusting Planing Depth (Fig. 1) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. Planing depth is infinitely variable from 0 to 2.5 mm. To adjust the cutting depth, rotate the depth adjustment knob/front handle (C) clockwise from the “0” position. Each click of the adjustment knob represents approximately 0.1 mm of depth. The cutting depth will increase from 0 to as much as 2.5 mm. It is recom mended that test cuts be made in scrap wood after each re-adjustment to make sure that the desired amount of wood is being removed by the planer. Several shallow passes (rather than one deep one) will produce a smoother finish. Planing (Fig. 2, 3, 4) CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turning the tool off. Hold the planer in the correct position with one hand on the front handle (C) and the other hand on the switch handle (D) as shown in Figure 2. Place the front of the shoe (E) on the surface to be planed, making certain that the cutting blades are not touching the surface. Push down firmly on the front handle of the planer so that the front shoe is ABSOLUTELY FLAT on the work surface. Squeeze the trigger switch and allow the motor to reach full speed before touching the planer blades to the surface. Move the tool slowly into the work and maintain downward pressure to keep planer flat. Be particularly careful to keep the tool flat at the beginning and the end of the work surface (Figures 2, 3, 4). Planing Tip: For a smoother appearance, fasten a piece of scrap wood to the the piece you are planing. Don’t stop planing until the cutting past your workpiece and into the scrap material. FIG. 2 CORRECT E D C FIG. 3 FIG. 4 INCORRECT INCORRECT Rabbet Fence (Fig. 5, 6) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments removing/installing attachments or accessories. CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turning the tool off. The rabbet fence can be installed on either side of your The planer can make rabbet cuts up to 12 mm. 5 To Install Rabbet Fence 1. Loosen the rabbet fence adjustment knob (G). 2. Slide the crossbar on the rabbet fence (F) into the hole near the front of the planer as shown in Figure 5. 3. Securely tighten rabbet fence adjustment knob (G) as shown in Figure 6. 4. The rabbet fence should be below the planer when installed correctly as shown in Figure 5. FIG. 5 FIG. 6 G F To Make a Rabbet Cut 1. To adjust the width of cut loosen rabbet fence knob (G), move fence to the desired position then securely tighten rabbet fence knob. 2. Make several cuts until the desired depth is reached. NOTE: It will be necessary to make quite a few cuts for most rabbet applications. To Change Blades (Fig. 7, 8, 9, 10) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. NOTE: The DW680- XE has two blades, one on each side of the blade drum, as shown in Figure 7. Any operation or adjustment should be made to both blades. Reversible Carbide Blades 1. To Remove Blade from Planer a. Loosen and remove the three hex head screws (J) with the 5 mm hex wrench provided. Remove the drum cover (K) from the drum (Q). b. Remove the blade carrier/guide bar assembly. Carefully remove the carbide blade (I). FIG. 7 M Q FIG. 8 I KQ L P J I FIG. 9 P M O N N J K L M P RM OPFIG. 10 LI 2. To Adjust Blade Using Gauge Plate (provided with tool) a. Cautiously place the carbide blade on the gauge plate (N) with the grooved side of the carbide blade facing up. Either edge of the reversible carbide blade can be set flush against the gauge plate inside wall (O). b. Place the blade carrier/guide bar assembly on the blade so that the rib on the blade carrier (L) fits into the groove on the carbide blade (I). The heel of blade carrier (M) will overlap the end of the gauge plate (N). c. Loosen the two hex screws (P) with the 2.5 mm hex wrench 6 d. Simultaneously push the blade carrier (L) and the guide bar (M) into the gauge plate inside wall (O), making sure that the carbide blade (I) is held firmly against the gauge plate inside wall (O) and securely tighten the two hex screws (P). 3. To Reinstall Blade a. Remove the adjusted blade carrier/guide bar assembly from the gauge plate (N) and place the heel of the guide bar (M) into the groove on the drum (Q). b. Place the drum cover (K) over the blade carrier/guide bar assembly. Loosely screw the three hex screws (J) into the drum (Q) so that there is a small gap between the drum and the blade carrier (L). c. Slide the carbide blade between the drum (Q) and the blade carrie...
Эта инструкция также подходит к моделям:Рубанки - N090451 (241.47 kb)