Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
D-2 Fig. D-1 6 - English FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION FOREWORD The Delta JT360 6" (152mm) Jointer with Stand is designed with a cutting capacity of 6" (152mm) width, 1/2" (13mm) depth and rabbeting 1/2" (13mm). Unit includes; heavy-duty 3/4 hp, 115/230 volt induction motor, stand, dust chute, center-mounted fence, three-knife cutterhead, cutterhead guard, and push blocks NOTICE: The manual cover illustrates the current production model. all other illustrations are representative only and may not depict the actual color, labeling or accessories and may be intended to illustrate technique only. CARTON CONTENTS 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 22 23 24 2 20 21 25 26 27 28 29 30 31 32 33 34 35 36 37 Fig. 4 Fig. 4A Fig. 4B 7 - English JOINTER PARTS Fig. 4 1. Motor and Switch 2. Jointer 3. Motor Pulley 4. V-Belt 5. Two Top End Braces for Stand (11-3/4") 6. Two Top Side Braces for Stand (15-3/4") 7. Two Lower Side Braces for Stand (20-1/2") 8. Two Lower End Braces for Stand (16-1/2") 9. Four Legs for Stand 10. Four Feet for Stand Legs 11. Cutterhead Guard 12. Fence Locking Handle 13. Fence Tilting Handle 14. Dust Chute 15. Dust Chute Cover 16. 6mm Allen Wrench 17. 4mm Allen Wrench 18. 3mm Allen Wrench 19. 2.5mm Allen Wrench 20. 12x14mm Open End Wrench 21. 8x10mm Open End Wrench 22. Rear Cutterhead Guard 23. Fence 24. Motor Pulley and Belt Guard Fig. 4A 25. Dust Collector Adapter 26. Push Blocks 27. Infeed Table Adjustment Rod, Handle, and Nut Fig. 4B 28. Special Studs (3) 29. 5/16-18x1." Carriage Bolts (4) 30. 5/16-18x3/4" Carriage Bolts (36) 31. M6x1x10mm Cheese Head Screws (4) 32. Wing Screws (2) 33. 5/16-18Hex Nuts (40) 34. 5/16 Flat Washers (36) 35. M10.2 Lockwashers for Special Studs (3) 36. M8.4 Flat Washer 37. M6.1 Lockwashers (4) UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. Jointer weight is approximately 175 lbs. Care must be taken when lifting jointer onto stand. A minimum of two people will be required to lift the machine. Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine. After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. 8 - English ASSEMBLY ASSEMBLY For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. ASSEMBLY TOOLS REQUIRED * 6mm Allen Wrench * 12x14mm Open End Wrench * 4mm Allen Wrench * 8x10mm Open End Wrench * 3mm Allen Wrench (All are supplied.) * 2.5mm Allen Wrench ASSEMBLY TIME ESTIMATE - 2-3 hours STAND 1. Assemble stand as shown in Fig. 5 using parts shown in Fig. 4. The parts for the stand (as shown in Fig. 4) are: 5. Two Top End Braces for Stand (11-3/4") 6. Two Top Side Braces for Stand (15-3/4") 7. Two Lower Side Braces for Stand (20-1/2") 8. Two Lower End Braces for Stand (16-1/2") 9. Four Legs for Stand 10. Four Feet for Stand Legs To assemble, insert the 5/16-18x3/4" carriage head bolts through legs and braces then place the 5/16" flat washers on the bolts and secure with the 5/16-18 hex nuts. Only tighten nuts finger-tight at this time. IMPORTANT: The top lips of two upper end braces (5) Fig. 5, must fit on top of the top lips of two upper side braces (6). 2. Assemble four rubber feet (10), to the bottom of each leg (9) as shown. DUST CHUTE TO STAND 1. The front of the stand is indicated by switch opening (B) Fig. 6, making the outfeed end of the stand (C) and the infeed end (A). 2. Assemble dust chute (E) Fig. 6, to outfeed end of stand (C) as shown. Align the four holes (D) Fig. 6, in the dust chute with the four holes in the stand. Insert a 5/16-18x3/4" carriage bolt through the hole in the dust chute and stand. Place a 5/16" flat washer onto the screw and thread a 5/16-18 hex nut onto the screw. Repeat this process for the three remaining holes in the dust chute and stand. Only tighten hex nuts fingertight at this time. 10 9 7 8 8 6 5 7 6 5 Fig. 5 A BD E D C D Fig. 6 MOTOR AND SWITCH TO STAND 1. Assemble motor (B) Fig. 7, to the bottom of the dust chute. Align the four holes (F) Fig. 7, in the dust chute, with the four holes in the motor mounting plate. Insert a 5/16-18x1."carriage bolt through hole in dust chute and hole in motor mounting plate. Place a 5/16" flat washer on screw and secure with a 5/16-18 hex nut. Repeat this process for the three remaining holes. Do not com plete ly tighten hex nuts at this time as the motor must be adjusted for proper alignment and belt tension later. C D BF F A Fig. 7 9 - English 2. Remove M4x.7x10mm pan head screws, M4.1 flat washers and M4x.7 hex nuts from two holes (A) Fig. 7 in switch. 3. Insert switch assembly (C) Fig. 7 from the inside of the stand. Align the holes (A) in the switch with t...