Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
1. Unplug the planer. 2. Slide the collar of the dust bag onto the exhaust port. NOTE: To remove the dust bag, pull it straight out of the exhaust port. CAUTION: The dust bag fills quickly. Empty it often to prevent damage to the product. ADJUSTING THE EXHAUST DIRECTION See Figure 3. Control the direction of debris when working in confined areas. Change the direction of the exhaust to either the right or left. Follow these steps to adjust the exhaust direction. 1. Unplug the planer. 2. Adjust the exhaust direction and dust bag: ¦ ¦¦¦¦¦To adjust exhaust to the right—Move the exhaust direction knob to the right and install the dust bag on the right exhaust port. ¦ ¦¦¦¦¦To adjust exhaust to the left—Move the exhaust direction knob to the left and install the dust bag on the left exhaust port. ADJUSTING THE PLANING DEPTH See Figure 4. Always work from a rough cut to a finish cut. The approximate setting for rough planing is 1/32 (0.8 mm). For finish planing use a setting of approximately 1/64 (0.4 mm). Make test cuts in scrap wood after each adjustment to make sure that the planer is removing the desired amount of wood. Follow these steps to adjust planing depth. 1. Unplug the planer. 2. Turn the depth adjustment knob to the desired setting. NOTE: To protect the blades during storage, transporting, etc., set the depth adjustment to 0. COLLAR DUST BAG EXHAUST PORT Fig. 2 Fig. 4 Fig. 3 EXHAUST DIRECTION KNOB DEPTH ADJUSTMENT KNOB Page 9 OPERATION OPERATION WARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in dust, shavings, chips, loose particles, or foreign objects being thrown in your eyes resulting in possible serious injury. If the operation is dusty, also wear a face or dust mask. STARTING/STOPPING THE PLANER See Figure 5. Follow these steps to start/stop the planer. ¦ ¦¦¦¦¦To start the planer—Push the lock-off button, and then depress the trigger switch. ¦ ¦¦¦¦¦To stop the planer—Release the trigger switch. OPERATING THE PLANER Follow these guidelines when operating the planer. ¦ ¦¦¦¦¦Clamp the work securely. ¦ ¦¦¦¦¦Support the work so that the operation is on your right. WARNING: Work moving during a cut could result in loss of control of the planer and cause serious injury. ¦¦¦¦¦ Hold the planer with both hands. Hold the front handle with your left hand and the rear handle with your right hand. ¦¦¦¦¦ Plane slowly and empty the dust bag often. CAUTION: Planing too fast results in a poor finish and increases chip build-up in the chip exhaust. Chip build-up restricts air flow and can cause motor overheating. WARNING: Do not attempt to clear a blocked chip exhaust until the blades stop and you have disconnected the product from the power source. Failure to heed this warning can result in serious personal injury. ¦¦¦¦¦ Keep the cord away from the work area. Do not allow the cord to hang on the work while planing. WARNING: Using the planer with a damaged cord could cause electrical shock resulting in serious injury. Fig. 5 LOCK-OFF BUTTON TRIGGER SWITCH THE KICKSTAND PIVOTS DOWN WHEN THE PLANER IS NOT IN USE THE KICKSTAND RETRACTS WHEN THE PLANER IS IN USE Fig. 6 KICKSTAND See Figure 6. Your planer has been equipped with an automatic pivoting kickstand that will prevent the blade from contacting the workbench when not in use. As you begin your planing operation, the kickstand will automatically retract as it passes over the edge of your work piece. When setting the planer down on your workbench, the kickstand will automatically pivot down to prevent the blade from making any contact. WARNING: Make sure the kickstand operates freely at all times and that the area surrounding the kickstand is clear of debris. Failure to do so could result in serious personal injury. Page 10 OPERATION OPERATION PLANING See Figure 7. Follow these steps to plane. 1. Clamp the work securely. 2. Adjust the planing depth. Refer to “Adjusting the Planing Depth” earlier in this manual. 3. Hold the front handle with your left hand and the rear handle with your right hand. WARNING: Always use two hands on the tool for any operation; this assures that you maintain control and avoid risk of serious personal injury. Always properly support and clamp the work so that both hands are free to control the planer. WARNING: Be careful to avoid hitting nails during planing operation; this action could nick, crack, or damage blades. 4. Place the front shoe on the edge of work to be planed. NOTE: Make sure the blades are not touching the work. 5. Apply pressure to the front handle so that the front shoe is completely flat on the work. 6. Start the planer and let the motor reach maximum speed. 7. Hold the planer firmly and push it forward into the work, using a slow, steady motion. 8. Apply downward pressure toward the rear handle as you reach the end of the planed cut.This helps keep the rear section of the planer base in contact with the work and prevents the front of the pl...