Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Stop tightening it when the drawer side and leg have approximately 3mm of clearance between each other. 6. Position the left side leg (C) on the floor and install the remaining (E4) barrel nuts into cross braces (D, E, & I) (Figure 5), and install cross brace (I) into the right leg. 7. Connect the left leg to cross braces (D, E, & I), and use a 5mm hex wrench to secure the braces to the leg with three (E2) flat washers, and three (E3) barrel bolts, but do not fully tighten at this time. 9. With the tilt-drawer in position as shown in Figure 6, install two (E4) barrel nuts in the remaining cross support (H), and secure it in place (Figure 7) between the legs with the remaining (E3) screws and (E2) washers. © Model H7725 (Mfg. since 7/09) 10. At this time tighten all of the (E3) barrel bolts except the (E9) barrel bolts used as the tilting-drawer hinge pins. 11. With the help of an assistant, return the workbench to the upright position, and lower the table top (A) onto the legs making sure to line up the pre-drilled holes in the legs and the underside of the workbench. 12. Working from the underside of the table legs, insert four (E8) screws and (E2) washers into the holes, and use the 4mm hex wrench to tighten the screws. 13. Insert the guide rods and leadscrew through the holes in the wood block (G) (Figure 8). Thread the leadscrew into the vise support until the wood block is slightly snug against the table and flush with the table top. Figure 8. Table vise installation. 17. Insert the tail vise wood block into the vise support block (Figure 9). Insert the tail vise leadscrew through the holes in the wood block and the vise support block at the edge of the table. 18. Turn the tail vise handle clockwise until the wood block just touches the table, and attach the vise plate as outlined in Steps 15 & 16. 19. Find the gas spring pins at the drawer underside, and install the gas springs (H5) with the two (H6) screws for each spring (Figure 10). 14. Keeping the wood block flush with the table top (Figure 8), drill two 5/e4M holes 17/ieM deep through the vise plate mounting holes and into the wood block. 15. Secure the vise plate to the wood block with two (H1) #5 x 17/ie" wood screws (Figure 8). 16. Under the table, place a cotter pin in the end of the leadscrew, bending only one cotter pin leg to a 90 degree angle. Model H7725 (Mfg. since 7/09) -3- Parts Breakdown and List Fastener k1^ 'S^l K^gH lE5^^^U k3Q Fastener Kit Part Numbers REF PART DESCRIPTION QTY £1 PH7725018 BARREL BOLT 2" 8 PI PH7725006 FLAT WASHER 18 FI PH7725024 BARREL BOLT 31/2" 8 ri PH7725025 LARGE BARREL NUT 8 tl PH7725019 SMALL BARREL NUT 8 n PAW05M HEX WRENCH 5MM 1 lil PAW04M HEX WRENCH 4MM 1 Kil PH7725031 WOOD SCREW 2" 4 ri PH7725014 SPECIAL SCREW 11/2" 2 ii(J PH7725032 COTTER PIN 2 n PH7725043 WOOD SCREW #5 x 17/ie" 4 |hJ PH7725016 BRASS TUBE 2 ! 1 PH7725015 LOCK WASHER 2 n PH7725020 KEY/LOCK SET 2 [hsJ PH7725010 GAS SPRING 2 |hJ PH7725011 FLAT HD SCREW 4 ri PH7725008 DRAWER PULL HANDLE 1 [hsJ PH7725009 SPECIAL SCREW 1" 2 REF PART DESCRIPTION QTY N PH7725001 TABLE TOP 1 n PH7725033 LEFT LEG 1 n PH7725002 RIGHT LEG 1 Id] PH7725026 TOP BACK CROSS BRACE 1 n PH7725034 TOP FRONT CROSS BRACE 1 I! PH7725040 CABINET TOP PANEL 1 H PH7725028 FRONT VISE 1 I! PH7725029 LWR FRONT CROSS BRACE 1 I] PH7725027 LWR BACK CROSS BRACE 1 U PH7725036 TAIL VISE 1 n PH7725023 DRAWER FACE 1 11 PH7725037 DRAWER BACK PANEL 1 u PH7725039 DRAWER RIGHT SIDE PANEL 1 11 PH7725038 DRAWER LEFT SIDE PANEL 1 [bpJ PH7725035 BOTTOM DRAWER PANEL 1 n G8589 GRIZZLY LOGO PLATE 1 -4- Model H7725 (Mfg. since 7/09)...