Войти:
Скачали: 0   Размер: 2 mb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name@name@name

Epreuve le Câblage d'Energie 1. Mise en marche le récepteur mais n'augmente pas le volume. La lumière d'energie du amplificateur devrait s'allumer. Si ne s'allume pas, révise le REM et le câble + 12 V. 2. Vous augmentez le volune du récepteur et tous les parlants devraient être en action. Sinon révise les connexions du clâvage dans l'amplificateur et les hauts-parleurs. Epreuve les Connexions du Clâvage Celle- ci épreuves assurent que les hauts-parleurs sont branchés convenablement. Si les h

Скачали: 0   Размер: 2 mb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name@name@name

The amplifier power light should come on. If not, check the REM and +12V wires. 2. Turn up the receiver volume slightly. All speakers should operate. If not, check wiring connections at amplifier and speakers. Test Speaker Connections These tests make sure the speakers are connected properly. If speakers don’t play at all, one (or both) speaker wires may be disconnected. Troubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and

Скачали: 3   Размер: 57 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

RIGHT - LEFT - LEFT+ GREENWHITEGRAYBROWNBLACK CHASSIS GROUND ONRADIO -6 128-5721 128-5721128-5721128-5721128-5721128-5721SHT. 8 OF 12 SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12 WARNING! l THIS AMPLIFIER IS DESIGNED FOR USE WITH 2 SPEAKERS l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. OUTPUT WIRING DIAGRAM OR GREASE FROM OR GREASE FROMOR GREASE FROMO

Скачали: 5   Размер: 64 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

Tighten the screw down to secure the wire. 1. Power Connection The battery terminal (+12V) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other w

Скачали: 0   Размер: 152 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can be screwed or bolted. 3. Remote Turn-On Connection The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car stereo is turned on. If the car

Скачали: 1   Размер: 89 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

We therefore advise that you read these instructions very carefully to familiarize yourself with the product and it's features. Should you require assistance with the installation or wiring of this unit, please call our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown. SPECIFICATIONS Maximum Output Power 4-Channel Operation: 125 watts x 4 2-Channel Operation: 500 watts x 2 Output Power @ 1% T.H.D. 4-Channel Operation: 600 watts RMS x 4 2-Channel Operation: 120 watts RMS x 2 Ou

Скачали: 1   Размер: 315 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

Wire the speaker leads from the car stereo to the 5-pin adaptor harnesses as shown in the diagram (shielded cable is not required for this application) and plug the connectors into the mating High-Level Input socket on the amplifier. Carefully splice and insulate all wire connections. CAUTION: Use either the low-level or the high-level inputs on the amplifier. DO NOT use both input levels at the same time. -7 USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. IMPORTANT RCA TYPE SHIELED CABLES (

Скачали: 0   Размер: 233 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

INSTALLATION INSTRUCTIONS MOUNTING SURFACE DRILL 1/8" HOLE SELF-TAPPING SCREW WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a 4-Channel, 3-channel, 2-channel, or mixed-mono application. The following pages illustrate the input and output wiring for these types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire connections for this amplifier are made via screw t

Скачали: 0   Размер: 607 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

BRIDGED BRIDGED BATT REM GND CH1 CH2 CH3 CH4 FUSE LEFT SPEAKER OR SUB-WOOFER 4-8 OHMS RIGHT SPEAKER OR SUB-WOOFER 4-8 OHMS 2-CHANNEL MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE #10 GAUGE WIRE (SEE TEXT) Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling off to a normal operating range.

Скачали: 0   Размер: 236 kb   Производитель: Audiovox  
Категория: Ресиверы и усилители
@name

Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the correspondi





Категории