Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Page 1 INSTALLATION .............................................. Page 3 LOCATING YOUR LOUDSPEAKERS, LOUDSPEAKER CONNECTIONS . Page 3 AUDIO & VIDEO CONNECTIONS................................ Page 4, 5 FRONT PANEL FUNCTIONS ................................... Page 5 SWITCHING ON AND SET UP MODE ............................ Page 5 INTRODUCTION Thank you for purchasing this Arcam product. The Xeta 2 is a sophisticated Home Cinema Dolby Pro Logic processor which offers superb sound and picture quality. It must be used with an integrated amplifier or a power amplifier to drive the front left and right speakers. The Xeta 2 is a little more complicated to connect up than an ordinary amplifier. Please read these instructions carefully and refer to the relevant diagrams on the following pages. Inside the front cover are diagrams of the Xeta 2's front and rear panels. Each input/output socket, function button and indicator is clearly numbered. The numbers correspond with those given in the instructions. For ease of use, the Xeta 2 is supplied with the CR40 infra-red remote control handset. Many functions are only available via the remote control. The Xeta 2 uses On Screen Graphics (OSG) which are displayed on your TV screen via the composite video MONITOR OUT © connection, to show which functions have been selected and which system adjustments have been set. If your TV does not have a composite video or SCART input it is not possible to view the On Screen Graphics in normal use, but it is still possible to use the Xeta 2 by following the BASIC SET UP procedure on page 8 and figure 6. Manufactured under license from Dolby Laboratories Licensing Corporation. Additionally licensed under one or more of the following patents: U.S. 3,632,886, 3,959,590; Canadian numbers 1,004,603 and 1,037,877. "Dolby", Pro Logic and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. USING YOUR XETA 2 REMOTE CONTROL COMMANDS............................... Page 9 GENERAL ADVICE ON USE.................................... Page 10 UPGRADE PATHS............................................ Page 11 CONNECTING TO POWER AMPLIFIERS .........................Page 11 SOURCES OF SURROUND MATERIAL...........................Page 11 SCART CONNECTIONS ....................................... Page 11 FAULT FINDING ADVICE ...................................... Page 12, 13 TECHNICAL SPECIFICATIONS ................................. Inside Back Cover SYSTEM CONFIGURATION You may choose from one of three basic connection configurations when using the Xeta 2, These are discussed below and illustrated in figures 1-3. 1. BASIC CONFIGURATION WITHOUT COMPOSITE VIDEO (see figure 1 ) The On Screen Graphics are not visible in normal use.The A/V source’s video signal is connected direcdy to the TV either on composite video or by the remodulated (RF)connection. Dolby decoding and processing is possible only with the A/V sources connected to the Xeta 2. Figure 1 2. USING THE XETA 2 AS AN INPUT EXTENDER FOR A/V SOURCES (see figure 2) Figure 2 shows the suggested wiring for use with a power amplifier (e.g. an Arcam Delta 290P, Xeta 290P) Delta 290 integrated amplifiers up to serial number 9934 or any other integrated amplifier without a spare tape monitor facility. Dolby decoding and processing is possible only on the audio from the A/V sources which are connected to the Xeta 2. The video sources are routed through the Xeta 2 and the composite video MONITOR OUT connection © is made to the TV to enable the On Screen Graphics to be seen. Figure 2 3. TAPE LOOP CONNECTION (see figure 3) This allows Dolby Pro Logic decoding and processing of all the sources connected to both the amplifier and the Xeta 2. This is the suggested configuration if you are using an Arcam A/V Delta 290 (serial no. 9935 onwards) These units are recognisable by the PROCESSOR/ TAPE 2 button on the front panel and a switch on the rear panel marked AV READY/NORMAL. The tape out connections of your stereo amplifier are connected to the AUX input of the Xeta 2. This allows sources connected to the stereo amplifier to be processed if required. The main front out connections of the Xeta 2 are connected to the tape in of the stereo amplifier in order to hear the left and right front signals. The PROCESSOR/TAPE 2 button on the Delta 290 must be pushed in to enable the signals to be processed via the Xeta 2. You should also set the AV READY switch to AV READY (see your Delta 290 handbook for details). This bypasses the Delta 290's volume control when the PROCESSOR/ TAPE 2 input is selected to allow the Xeta 2 to control the volume level of the system. If the tape or processor loop of your amplifier has been used up by the connections to the Xeta 2, then your cassette deck should be connected to the TAPE IN © and TAPE OUT © of the Xeta 2. The monitoring of the tape deck, provided it is a 3 head model, is carried out by use of the TAPE button on the X...