Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
CD, to a tape deck connected to the amplifi er, first select the CD input with the input selector bq. Set your tape deck into its record mode. Press PLAY on your CD player. The CD signal will now be recorded onto your cassette deck. If your cassette deck is a 3-head type it is possible to monitor the actual recording on the tape. To do this push the TAPE button br in. Switching this button in/out enables you to do an A/B comparison between the source signal and the recorded signal. Using a remote control The A65 and A75 offer remote control of the input selection, volume control and mute via the CR-389 remote handset supplied. It may also be possible to operate these functions with other remote control handsets that use the Philips RC-5 protocol. If the amplifiers are muted via remote control, the power indicator glows orange. To cancel the mute function, press MUTE again or either of the volume up/down buttons on the remote control handset. If you mislay the handset after muting the amplifier, turn it off with the POWER switch cp for 20 seconds, then switch it back on again to allow the internal mute system to reset. A65/A75/P75 6 A65/A75/P75 7 FM DAB PROG DISP RPT MODE BAND 1-9 2-10 3-11 FM DAB SEL TUNER CR-389 CD AMPLIFIER AV DVD VCR TAPE PHONO AUX CD TUNER ENTER SP1 SP2 DISP MENU DISP 4-12 5-13 6-14 7-15 8-16 Using the remote control CR-389 Remote Control The CR-389 remote control gives access to all functions available on the front panel. It also has controls to operate Arcam CD players, AM/FM and DAB tuners. Input selection buttons These operate in the same way as the input selector on the front panel of your integrated amplifi er. Volume and Mute ( ) Press + to increase volume or – to decrease the output volume on the amplifi er. Press to mute the speaker connections and preamp outputs. Both tape outputs and the headphone socket remain active. Mute is disabled either by pressing again, or by adjusting the volume. Tuner controls These offer basic control of Arcam tuners. NOTE: Remember to install the two supplied AAA batteries before trying to use your remote control! Do not place anything in front of the IR receiver on the left of the A65 or A75, or the remote control may not work. CD controls These offer basic controls of Arcam CD players. Not used with A65/A75 These control features of other amplifi ers in the Arcam range. Not used with A65/A75 The Power/Standby button does not operate with the A65 and A75 amplifi ers. Installation: P75 power amplifier The P75 power amplifier can be used in conjunction with the A65 and A75 integrated amplifiers (or other Arcam amplifiers) to bi-amplify loudspeakers that have two pairs of input connections (i.e. are bi-wireable). The P75 can also be used with a pre-amplifier such as the Arcam 9C or an AV processor or amplifi er with PRE-AMP OUT sockets. Loudspeaker connections Connect up following the instructions for installing the A65 and A75 integrated amplifiers (see page 4). Connecting to other equipment PWR AMP IN 5 Connect these sockets to your preamplifier output sockets. Alternatively, if you are using an integrated amplifier (as your pre-amp) such as the A65, A75 or Alpha series amplifiers, connect the PWR AMP IN sockets to the PRE AMP OUT sockets on those amplifiers. MONO LINK 6. The P75 can be adapted to provide two mono loudspeaker outputs from a single input. Pull out the U-link 8 supplied and use it to connect the MONO LINK sockets 6 together. Utilising one P75 power amplifier per loudspeaker will enable you to bi-amplify bi-wireable loudspeakers. This is particularly beneficial for top quality stereo installations with a separate preamplifier, or for the left, centre and right channel loudspeakers in a five speaker Dolby Pro Logic™ or Dolby Digital™ system. Contact your Arcam dealer for more detailed information. DAISY CHAIN The P75 is capable of driving further P75 amplifiers (or any other power amplifier), to drive more speakers (e.g. those in other rooms or tri-amplified speakers etc). Connect the extra power amplifier inputs to the MONO LINK outputs 6 left to left, right to right with suitable high quality phono to phono cables. Connecting to a power supply Connect up following the instructions for installing the A65 and A75 integrated amplifi ers (page 4). CIM MODULE 7 The CIM (custom install module) is an optional module that enables you to adjust the gain of the left and right channels of the power amplifier independently and also to switch the power amplifier on/off remotely, with a 12 volt trigger. The CIM module would normally be used in a multi-room set up. When a CIM module is fitted into a power amplifier, the front panel power switch is disabled. See your Arcam dealer for further information. Using the power amplifier SP1 DIRECT terminals 3 Are switched off when a headphone jack plug is inserted in the headphone socket bk on the front of the amplifier or, by pressing the MUTE button ( ) on the remote control handset. SP2 9 Push the butt...
Эта инструкция также подходит к моделям:Ресиверы и усилители - A65 (1.15 mb)
Ресиверы и усилители - P75 (1.15 mb)
Ресиверы и усилители - A65 (1.15 mb)
Ресиверы и усилители - P75 (1.15 mb)