Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
c) [Position] Input the satellite position. d) [Angle] Degree: Enter the degree of the satellite position on the sky. e) [Reset] Click the [Reset] button to drive the dish to zero position. f) [Stop] Click the [Stop] button to stop the motor. g) [Close] Click the [Close] button to exit the window. 14 ENUTV-DVB-S User’s Guide 3.2 Channel Scanning Click the [Scan] button to display the Program Scan menu. In the menu, you can click the small pane to select transponder under the current satellite to search channels. You can also click the [Select All] button to select all transponder to scan channel. All the searched channels will be displayed in the bottom of the menu. 15 ENUTV-DVB-S User’s Guide 3.3 Transponder Parameters 1. Add transponder Add a new transponder in the transponder list. The following figure is transponder parameter dialog box. a) Name: Enter the new name of the TP. b) [Frequency (MHz)] This box indicates the down link frequency of the current transponder. c) [Symbol Rate (KS/s)] This box indicates the symbol rate of the current transponder. d) [Polarity] This box shows the LNB power supply mode. There are [Vertical], [Horizontal] polarization and [Disable] for your choice. 16 ENUTV-DVB-S User’s Guide 2. Modify transponder Click the [Modify] button in the [transponder] item. The transponder parameters dialog box will pop up again. 3. Delete transponder Delete a transponder in the transponder list. Select one transponder and press Del. 4. Scan Auto search all the programs. 3.4 IP Receiver This page shows the program table of the current transponder. You can setup the PID parameters which the satellite service provider offers. If there is no any setting about current transponder in transponder parameters item, all operations in this page are prohibited. Please add new transponder before you enter the following page. You can also double click the icon on the desktop to display the IP Receiver window. 1. Transponder The box shows all of the TPs under the current satellite. You can choose them. 2. Satellite The box shows all of the selected satellites. 17 ENUTV-DVB-S User’s Guide 3. Available PID Show searched data PID under the current transponder in the table. (Standard PID) 4. Active PID This item shows the current active PID. 5. PID (Hex) Input the PID provided by your service provider. 6. Add PID Add PID value in [PID] and in Available PID table into active PID table. It can be added to 64 PIDs at the most. 7. Delete PID Delete the selected PID in the active PID table. 8. Filter Type Two filter types are available: MAC filter and Dial IP filter. MAC Filter: Filter data packets per the receiving box’s MAC address. If the destination address in the data packet is as the same as MAC address of the box, the packets will be received. If not, the packets won’t be received. Dial IP Filter: Filter data packets per the IP address assigned by server. 9. Unicast and Multicast MAC: To show the MAC address of the receiver box. Data Rate: To show unicast and multicast data rate in unit time. NOTE: In any circumstance the broadcast and multicast data will pass it. 18 ENUTV-DVB-S User’s Guide Chapter 4: Application Programs 4.1 Capture Click the button to open the capture dialog box. When playing, click [Capture] button to capture one still picture and add to the capture window. Click [Save] button to store the captured picture. Click [Delete] button to delete the selected picture from the storing folder. Click [Del ALL] button to delete all the pictures shown on the capture window, and delete them in the storing folder. 4.2 Record Scheduler When in playing status, click the button to open the scheduler dialog box to create or edit the pre-set recording tasks. Click [Add] button to add one recording channel. Click [Delete] button to delete the recording channel. Click [Clear] button to clear the recording channel. Note: You can set the start time and how long you want to record your favorite programs. 19 ENUTV-DVB-S User’s Guide When the program broadcasts to the starting time that you have established just now, the state appears of recording and producing the button. If you want to watch programs that you record and produce, click button, it will broadcast from TV window switch over to record programs window, then select the recording program that you want to watch from right column, pressing the right key can be loaded and recorded the file. 4.3 EPG Just activate in playing channel status, click the button to get EPG information of channel. 4.4 System Setting In the main menu, click the right key on the mouse to display the system setting menu. You can also click the “setting” on the file bar on the top of menu. 1. Path (1) Click the Browse button to select the path of the recording file to be saved. (2) Click the Browse button to select the path of the capturing picture to be saved. 20 ENUTV-DVB-S User’s Guide 2. Advanced (1) Decoder: Click the “ ” to select the MPEG decoder. (2) Time Zone: Click the “ ” t...