Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
(Whenever playing at full output levels, it is recommended that you use the Speakon® jacks.) 14. STEREO/DUAL MONO / MONO BRIDGE: Use this switch to set the operating mode of the amplifier. When the switch is out, the amplifier is in the Stereo or Dual Mono Mode; when the switch is depressed the amplifier is in the Mono Bridge Mode. In the Stereo mode, use the Power Amp A input (#18) and the Sensitivity Channel A control (#1) for the LEFT channel, and the Power Amp B input (#15) and the Sensitivity Channel B control (#7) for the RIGHT channel. This is recommended since the Sensitivity Channel A control is positioned on the left of the amplifier and the Sensitivity Channel B control is positioned on the right. (Left controls left, right controls right...) 15. POWER AMP B POWER AMP INPUT: When operating the SVP1600 in the Stereo mode, use this jack to connect the right channel input signal to the amplifier. 16. POWER AMP B PARALLEL OUTPUT: Use this jack to send the Power Amp B Input signal to the Power Amp B Power Amp Input jack of a second SVP1600 amplifier. This jack is active when the SVP1600 is operated in either the Stereo or Dual Mono mode. 17. POWER AMP A PARALLEL OUTPUT: Use this jack to send the Power Amp A Input signal to the Power Amp A Power Amp Input jack of a second SVP1600 amplifier. This jack is active when the SVP1600 is operated in any mode. 18. POWER AMP A POWER AMP INPUT: When operating the SVP1600 in the Stereo mode, use this jack to connect the left channel input signal to the amplifier. When operating the SVP1600 in the Dual Mono or Mono Bridge mode, use this jack to connect the mono input signal to the amplifier. Operation: Mono Bridge Mode: 7 43565 155S31V P 91S6VP016000 (21) SERIAL# BMCDN20083 Line: 120V Freq: 60 Pwr: 1.4kVA IN FROM PREAMP OR EFFECT'S OUTPUT MONO BRIDGE HIGH POWER CABINET(S) 4 OHMS MINIMUM NOTE: THE SPEAKER CABINET(S) MUST BE ABLE TO HANDLE THE EXTREMELY HIGH POWER OUTPUT OF THE MONO BRIDGED AMPLIFIER Set the Stereo/Dual Mono / Mono Bridge switch to the Mono Bridgel position (switch in/depressed). Connect a shielded signal cable from the Output of your Preamp or Effect to the Power Amp A Power Amp Input jack. Connect a speaker cable from the SVP1600’s Mono Bridge Speaker Output jack to the input jack(s) of the speaker(s). NOTE: The Speakon® cable must be wired as follows: 1+ = hot, 2+ = return. Operation: Dual Mono Mode: 7 43565 155S31V P 91S6VP016000 (21) SERIAL# BMCDN20083 Line: 120V Freq: 60 Pwr: 1.4kVA OUT FROM PREAMP OR EFFECT'S OUTPUT STEREO/ DUAL MONO CABINET(S) 2 OHMS MINIMUM CABINET(S) 2 OHMS MINIMUM Set the Stereo/Dual Mono / Mono Bridge switch to the Stereo/Dual Mono position (switch out). Connect a shielded signal cable from the Output of your Preamp or Effect to the Power Amp A Power Amp Input jack. Connect a speaker cable from the SVP1600’s Power Amp A Speaker Output jack to the input jack(s) of one (set) of the speakers. Connect a speaker cable from the SVP1600’s Power Amp B Speaker Output jack to the input jack(s) of the other speaker(s). NOTE: The Speakon® cable must be wired as follows: 1+ = hot, 1- = ground. 6 SVP1600 Stereo Bass Power Amplifier 7 System Block Diagram: SVP1600 Stereo Bass Power Amplifier SPEAKER OUTPUT A SPEAKER OUTPUT B SPEAKER OUTPUT B SPEAKER OUTPUT A SPEAKON® SPEAKER OUTPUT MONO BRIDGE 1+ 2+ 1- 2- SPEAKON® SPEAKER OUTPUT A SPEAKON® SPEAKER OUTPUT B 1+ 2+ 1- 2- LIMIT DEFEAT POWER AMP A STEREO/ DUAL MONO MONO BRIDGE POWER AMP B POWER AMP A INPUT / MONO SENSITIVITY CHANNEL A SENSITIVITY CHANNEL B POWER AMP B INPUT LIMITER LIMITER 1+ 2+ 1- 2- POWER AMP A PARALLEL OUTPUT POWER AMP B PARALLEL OUTPUT LIMIT LED B LIMIT LED A Operation: Stereo Mode: 7 43565 155S31V P 91S6VP016000 (21) SERIAL# BMCDN20083 Line: 120V Freq: 60 Pwr: 1.4kVA OUT FROM STEREO PREAMP OR STEREO EFFECT'S LEFT OUTPUT FROM STEREO PREAMP OR STEREO EFFECT'S RIGHT OUTPUT STEREO/ DUAL MONO LEFT CHANNEL CABINET(S) 2 OHMS MINIMUM RIGHT CHANNEL CABINET(S) 2 OHMS MINIMUM Set the Stereo/Dual Mono / Mono Bridge switch to the Stereo/Dual Mono position (switch out). Connect a shielded signal cable from the Left Output of your Stereo Preamp or Stereo Effect to the Power Amp A Power Amp Input jack. Connect a shielded signal cable from the Right Output of your Stereo Preamp or Stereo Effect to the Power Amp B Power Amp Input jack. Connect a speaker cable from the SVP1600’s Power Amp A Speaker Output jack to the input jack(s) of the Left Channel speaker(s). Connect a speaker cable from the SVP1600’s Power Amp B Speaker Output jack to the input jack(s) of the Right Channel speaker(s). NOTE: The Speakon® cable must be wired as follows: 1+ = hot, 1- = ground. SVP1600 Stereo Bass Power Amplifier Technical Specifications OUTPUT POWER RATING 1600 Watts Mono-Bridged @ 4 Ohms (1200 Watts Continuous) 1200 Watts Mono-Bridged @ 8 Ohms (900 Watts Continuous) 2 x 900 Watts @ 2 Ohms (600 Watts Continuous) 2 x 625 Watts @ 4 Ohms (490 Watts Continuous) 2 x 350 Watts @ 8 Ohms (300 Watts Continuous) F...