Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
This type of receiver provides superior performance by preventing loss of signal due to multi-path interference. In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some other devices. Transmitters are used to activate or control the devices. The receiver should be mounted indoors or inside a weather resistant non-metallic housing for outdoor use. The digital DX/DXS code format features over a million possible codes. The transmitters are precoded at the factory to unique codes, so no field coding is required. For versatility, any transmitter can be programmed into any receiver channel. Receivers must be programmed to recognize the transmitter’s code before system testing and operation. Up to 32 transmitters can be programmed into the receiver. Each button on multi-button portable transmitters send a unique code, and are programmed as separate transmitters. The CHANNEL display shows the channels activated and the presence of radio activity. Individual indicators for ALARM, STATUS, and LOW BATT show the supervisory status of each receiver channel. All outputs can be configured for normally open or normally closed. The units can be powered from a 10.2-14.4 VDC or 12-16 VAC power source. The units will draw about 35 mA standby and up to 120 mA in alarm. FEATURES COMPONENT LOCATIONS OPTION JUMPERS AND CHANNEL BUTTONS DETAIL MOUNT RECEIVER ATTACH ANTENNAS CONNECT TERMINALS (760) 438-7000 • FAX (760) 438-7043 CHANNEL BUTTON ACCESS PANEL CHANNEL DISPLAY ALARM, STATUS, & LOW BATTERY INDICATORS CASE LOCKING SCREW OPEN CASE TO VIEW COMPONENTS LEFT ANTENNA TERMINAL CHANNEL DISPLAY ALARM INDICATOR STATUS INDICATOR LOW BATTERY INDICATOR RADIO ACTIVITY INDICATOR RIGHT ANTENNA TERMINAL AUDIO TEST POINT GROUND TEST POINT OUTPUT POLARITY JUMPER PROGRAM JUMPER TERMINAL BLOCK WIRING STRAIN RELIEF POSTS RECESSED WIRING ACCESS HOLE CHANNEL BUTTONS OUTPUT JUMPERS STATUS JUMPERS CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 CHANNEL 6 CHANNEL 7 CHANNEL 8 DXSR-1508 ONLY CHANNEL BUTTON OUTPUT JUMPER STATUS JUMPER CHANNEL BUTTONS ARE USED DURING PROGRAMMING AND TO UNLATCH THE CHANNEL'S OUTPUT IN LATCHED MODE OUTPUT JUMPERS SELECT MOMENTARY, TOGGLE, OR LATCHED OUTPUT FOR EACH CHANNEL WHEN A CHANNEL'S STATUS JUMPER IS CUT, THE CHANNEL WILL REQUIRE STATUS TRANSMISSIONS FROM A SUPERVISED TRANSMITTER PROGRAMMED INTO THAT CHANNEL MOUNT RECEIVER AS HIGH AS PRACTICAL USING THE SCREWS AND SCREW ANCHORS PROVIDED COVER THE SCREWS WITH THE FOUR SCREW HOLE PLUGS PROVIDED INSTALL THE TWO ANTENNAS UNDER THE LEFT AND RIGHT ANTENNA TERMINALS TIGHTEN ANTENNA TERMINALS WITH ANTENNA WHIPS ABOVE THE SCREW AND UNDER THE TERMINAL PLATE AS SHOWN (BE SURE CASE COVER SLOTS ALIGN WITH ANTENNAS) NEG +12V LOW BAT STAT CH1 CH2 CH3 CH4 COM CH5 CH6 CH7 CH8 COM MODEL DXSR-1508 ONLY SECURE WIRES WITH ZIP-TIE FROM POWER SOURCE 10.2-14.4 VDC OR 12-16 VAC 120 mA MINIMUM OUTPUTS TO DEVICE TO BE TRIGGERED 100 mA MAXIMUM PER OUTPUT WITH OUTPUT POLARITY JUMPER IN PLACE, ALL OUTPUTS WILL SWITCH TO COMMON WHEN ACTIVE NOTE: SEE WIRING EXAMPLES ON REVERSE SIDE OF THESE INSTRUCTIONS WIRING EXAMPLES SELECT OPTIONS ADDING TRANSMITTERS REVIEWING MEMORY REMOVING TRANSMITTERS SYSTEM OPERATION SUPERVISORY CONDITIONS INTERNATIONAL WARRANTY Copyright © 2003 Linear Corporation 215648 D NEG +12V LOW BAT STAT CH1 CH2 CH3 CH4 COM CH5 CH6 CH7 CH8 COM MODEL DXSR-1508 ONLY NEGATIVE +12 AUX ZONE 1 COM ZONE 2 ZONE 3 COM ZONE 4 EXAMPLE RELAY HOOK-UP CONTROL PANEL RECEIVER NOTES: 1. ZONES ARE NORMALLY OPEN WITH END-OF-LINE RESISTORS 2. LOW BATTERY AND STATUS OUTPUTS ARE COMBINED TO TRIGGER ZONE 4 AS TROUBLE TO +12 VOLTS TO RECEIVER OUTPUT N.C. N.O. COM 12 VOLT RELAY 1N4001 DIODE EXAMPLE 4-ZONE CONTROL PANEL HOOK-UP EXAMPLE BEEPER HOOK-UP TO RECEIVER OUTPUT TO +12 VOLTS PIEZO BEEPER EXAMPLE L.E.D. HOOK-UP 1K OHM L.E.D. TO +12 VOLTS TO RECEIVER OUTPUT JUMPER IN THIS POSITION (FACTORY SETTING) CAUSES A MOMENTARY 3/4 SECOND OUTPUT WITH EACH ACTIVATION SET OUTPUT JUMPERS FOR EACH CHANNEL USED JUMPER IN THIS POSITION CAUSES A TOGGLE OUTPUT, EACH ACTIVATION WILL CAUSE THE OUTPUT TO SWITCH FROM OFF TO ON, OR, ON TO OFF JUMPER REMOVED CAUSES OUTPUT TO LATCH UNTIL RESET BY A RESTORE TRANSMISSION (DXS-31 DOOR CLOSED) OR RESET BY PRESSING THE CHANNEL BUTTON (JUMPER CAN BE STORED ON SINGLE PIN) CUT STATUS JUMPERS FOR ANY CHANNELS THAT REQUIRE STATUS TRANSMISSION MONITORING USE SMALL CUTTERS TO CUT JUMPERS IF NORMALLY CLOSED OUTPUTS ARE REQUIRED, REMOVE THE OUTPUT POLARITY JUMPER MOMENTARY OUTPUT TOGGLE OUTPUT DOOR & WINDOW LATCHING OUTPUT 1 2 3 4 REMOVE THE PROGRAM JUMPER, THE CHANNEL DISPLAY SHOWS "P" BRIEFLY PRESS THE BUTTON FOR THE CHANNEL THAT THE TRANSMITTER IS GOING TO BE ADDED INTO, THE CHANNEL NUMBER SHOWS ON THE DISPLAY YOU HAVE 5 SECONDS TO ACTIVATE THE TRANSMITTER, THE ALARM LED WILL BLINK AFTER THE TRANSMITTER IS ENTERED, OR AFTER 5 SECONDS, THE CHANNEL DISPLAY WILL RETURN TO "P" REPEAT STEPS 2 & 3 FOR ADDI...
Эта инструкция также подходит к моделям:Ресиверы и усилители - DXSR-1508/EC (260.42 kb)