Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
For your safety, keep ladder and antenna away from power lines. Contact may NEC - National Electrical Cod e *Antenna Discharge Unit is notrequired if lead in conductors areenclosed in a continuous metallicshield that is permanently and IMPORTANT READ BEFORE INSTAL- LATION Antenna grounding and safety warning 1. Outdoor antennas and lead-in conductors from antenna to a building, should not cross over open conductors of electric light or power circuits. They should be kept away from all circuits to avoid the possibility of accidental contact. 2. Each conductor of a lead-in from an outdoor antenna should be connected with an antenna discharge unit. Antenna discharge units (or Lightning Arrestor) should be located outside the building or inside the building between the point of entrance of the lead-in and the TV, and as near as practical to the entrance of the conductors to the building. Important Safety Notes If you do not feel comfortable or competent to install this antenna we recommend that you seek the assistance of a qualified professional antenna installer. Read the instructions for this device thoroughly before attempting installation. The installation or dismantling of any antenna near power lines is dangerous. Each year hundreds of people are killed or injured while attempting to install or service antennas. For your safety and proper antenna installation, read and follow all safety precautions. Choose an installation site for safety as well as performance. All electric power lines, cable lines and telephone lines look alike. To be safe, assume ANY overhead line can kill you. Do not place an antenna where it could potentially fall on to, or blow into a power line. If in doubt call your electric provider. Let them review your site. Outdoor antennas should be grounded with an approved 3 EN Safety Instructions EN Safety Instructions IMPORTANT READ BEFORE INSTAL- LATION lighting arresting device. Local codes may apply. Use 8 AWG or larger ground wire. Height or other restrictions on antennas may apply to your installation depending on your proximity to an airport, or local ordinances. Take the time to plan your installation procedure. Do all assembly work on the antenna on the ground. Raise the completed antenna after assembly. Do NOT work on a wet, snowy or windy day or if a thunderstorm is approaching. Do NOT use a metal ladder. If the antenna assembly starts to fall, get away from it and let it fall. Remember that the antenna mast and cable are all excellent conductors of electrical current. Do NOT install the antenna by yourself. Be sure that there are two other people available for help. If any part of the antenna should come in contact with a power line . . . DON'T TOUCH IT OR TRY TO REMOVE IT YOURSELF. Call your local power company immediately. They will remove it. Should an electrical accident occur . . . DON'T TOUCH THE PERSON IN CONTACT WITH THE POWER LINE, or you too can become electrocuted. Instead, use a DRY board, stick, or rope to push or pull the victim away from the power lines and antenna. Once clear, check the victim. If he has stopped breathing, immediately administer cardiopulmonary resuscitation (CPR) and stay with him. Have someone else call for medical help. Install wire antennas high enough that they will not be "walked into" by people. Do not install antenna wire(s) over or under utility lines. 4 ENIncluded with ENIncluded with Note: For final installation and connection of your antenna, additional hardware may be required. Before starting assembly, please read through the instructions carefully to determine your Parts included: a. UHF B o o m -A . . . . . . . . . . . . 2 b. UHF Boom-B . . . . . . . . . . . . 2 c. VHF Boom-A . . . . . . . . . . . . 1 d. VHF Boom-B . . . . . . . . . . . . 2 e. Reflector Elements . . . . . . . 2 f. 46. Element . . . . . . . . . . . . 2 g. 50. Element . . . . . . . . . . . . 2 h. Tubing Brace . . . . . . . . . . . . 2 j. Phasing Wire . . . . . . . . . . . . 2 k. Reflector Brackets . . . . . . . . 2 lPivot Brackets 4 . . . . . . . . . . n. Locking Brackets . . . . . . . . . 4 p. End Caps . . . . . . . . . . . . . . . 8 q. Screws (1-3/4.) . . . . . . . . . 5 r. Screws (1-1/2.) . . . . . . . . 1 0 s. Screws (3/4.) . . . . . . . . . . 2 t. Lock Washers/ Washers . 6, 4 u. Wing-Nuts . . . . . . . . . . . . . 1 7 v. Nuts . . . . . . . . . . . . . . . . . . 6 Assembly w. Band Separator . . . . . . . . . . . . 1 x. U-Bolt . . . . . . . . . . . . . . . . . 3 y. Cross Piece (for U-Bolt Assembly) 3 z. Antenna Saddle . . . . . . . . . . 1 *Quantities listed include those which may already be attached to antenna NOTE: Cable, mast and mounting brackets are not included. 5 EN Assembly EN Assembly 6 Assembly of UHF Portion • Rotate reflector element rods into place. NOTE: When rotating element rods, grasp close to pivot and relieve spring pressure on pivot bracket detents. Don’t apply excess pressure to reflector element rods. • Insert UHF Boom-A into UHF Boom-B and...