Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
It is essential for proper operation of this antenna system that the power injector be connected between the antenna and any devices such as splitters, additional amplifers, matching transformers, networks, etc. SEE DIAGRAM TO LEFT. Disregarding this important notice may result in damaging the power injector or improper operation / poor performance. 4 ENIncluded with Antenna ENIncluded with Antenna Parts included: 1. MANT950 Antenna 1 2. 12VDC, 200mA Power Injector 1 3. Main Bracket 1 4. 1/2" screws & washers) 6 5. U-Bolts 2 6. Mast clamps 2 7. Wing-nuts 4 7. L-Bracket 2 8. 2" Wood Screws 2 9. 20' RG-59U cable with connectors 1 10. Weather Boot 1 Mounting Antenna Fig A Determining signal strength Before Installation determine the best location for optimum reception. It is important for the antenna to have an unobstructed path to the transmitter.To determine the transmitter(s) location you can consult the website For best results the antenna should be facing to the transmitter locations as shown at left. Wall mounting the unit (indoor or outdoor) Do all the antenna assembly work on the ground. Raise the completed antenna after assembly. 1. Attach the main bracket to the antenna assembly using the 6 - 1/8” screws and washers as shown in Figure A. 2. Attach the L brackets to the unit as shown in figure B. Note that the brackets are adjustable laterally for best mounting. 3. Using the L brackets as a guide mark position for the two 2” wood screws. If possible locate a stud to screw into, adjusting the L brackets accordingly. If studs are not available use appropriate wall anchors (not included, available at any hardware store). Screw the wood 5 EN Mounting Antenna EN Mounting Antenna Fig B Fig C screws into the wall but leave about 1/2” to allow for the last step. 4. Attach the cable to the F connector on the underside of the unit and slide the weather protection boot over the connection. 5. Hook the top of the L brackets onto the wood screws through the keyholes. Make sure the screws are at the top of the keyhole. At this point tighten the wood screws fully into position and tighten the L bracket screws. Mast Mounting or Attic Mounting (Mast not included) Do all the antenna assembly work on the ground. Raise the completed antenna after assembly. 1. Install the two U-bolt s from the rear of the main bracket. 2. Attach the main bracket to the antenna assembly using the 6 - 1/8” screws and washers as shown in Figure A above. 3. Attach the U-Bolt clamps with the pointed side facing outward. 4. Place the 4 wing-nuts on the threads of the U-bolts – loosely allowing space for the mast. 5. Slide the top of the mast under the clamps – and fully tighten the wing-nuts. The completed assembly should look like figure C. 6. Attach the cable to the F connector on the underside of the unit and slide weather protection boot over the connection. 7. Attach the mast to the mast mount and fasten hardware for the mast (not included). Connecting to your TV As previously noted the power injector must be placed in-line between the antenna and before any splitter or additional devices. 1. Connect the coaxial cable from the antenna to the F connector labeled ANT on the power injector. 2. Connect the short lead from the power injector to the antenna input on your TV. 3. Connect the power supply lead to the power injector, then plug the power supply into a 110/120 Volt AC receptacle. 6 ENConnecting to your TV ENConnecting to your TV S SSa aaf ffe eet tty yy N NNo oot tte ee - --T TTh hhe ee p ppo oow wwe eer rr i iin nnj jje eec cct tto oor rr a aan nnd dd p ppo oow wwe eer rr s ssu uup ppp ppl lly yy i iis ss f ffo oor rr i iin nnd ddo ooo oor rr u uus sse ee o oon nnl lly yy! !! Alternate connections 1. If your TV has separate inputs for UHF and VHF you will need to purchase a signal splitter that will separate the two different signals 2. If your TV has only two screw type antenna inputs you will need to purchase a 75 Ohm to 300 Ohm transformer. A note about coaxial cable –Your Mant 950 includes a 20 foot roll of RG-59 coaxial cable. If you should find that this is not adequate for your needs we recommend for best possible signal integrity that you do not extend this cable.A better choice is to replace the cable with either RG-6 or RG-6 Quad Shield cable. Both of these cables are designed for minimal signal loss over longer cable runs. This will ensure the best possible picture and overall performance. Warranty Limited Lifetime Warranty The manufacturer warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specifications and warnings, for as long as you own this product. This warranty extends only to the original purchaser of the product, and is not transferable. Defective products, together with the dated proof of purchase, must be returned to the place of purchase for repair or replacement.THERE ARE NO OTHER EXPRESS WARRANTIES. ...