Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
% MUTE key ^ Use to temporarily mute the sound. ^ SOUND key ^ Use to adjust the sound quality and ambi ence effects. & LISTEN MODE key . Use to select the listening mode. * SETUP key $ Use to select the surround sound settings. 0 ! @ # $ % ^ & * Setting up the system KRF-V8010D (En/T) Microcomputer malfunction If operation is not possible or an erroneous display appears, even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. ¤ To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions, including projections) equal to, or greater than shown below: Left and right panels: 10 cm, Rear panel: 10 cm, Top panel: 50 cm Caution regarding placement Make connections as shown below. Connecting audio components When connecting the related system components, be sure to also refer to the instruction manuals supplied with the Shape of AC outlets components you are connecting. Do not connect the power cord to a wall outlet until all connections are completed. SYSTEM CONTROL jacks ! For U.K. x2 Australia x1 Other countries x2 Notes 1. Connect all cords firmly. Loose connections may prevent proper sound transmission or produce noise. 2. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging / unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. 3. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit. Preparations REC OUT PHONO CD MD / TAPE MONITOR PLAY IN REC OUT PLAY IN L R To AC wall outlet Cassette deck or MD recorder CD player IN OUT Cassette deck or graphic equalizer & IN OUT OUT OUT Record player Setting up the system Preparations VIDEO 1VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 1 VIDEO 2/ DVD 6CH. VIDEO 3/ DVD 6CH. REC OUT PLAY IN PLAY IN PLAY IN MONITOR VIDEO INVIDEO OUT OUT OUT IN Video Inputs Video inputsand outputs(Yellow RCA pin cords) OUT Video deck DVD player or LD player DVD player or LD player OUT OUT OUT IN Audio inputs and outputs(Red and white RCA pin cords) VIDEO IN (Yellow RCA pin cord) Monitor TV A video component with digital audio outputs should be connected to the VIDEO2 or VIDEO3 jacks. KRF-V8010D (En/T) Connecting video components Digital connections The digital in jacks can accept either Dolby Digital (AC-3) or PCM signals. Connect components capable of outputting Dolby Digital (AC3) or standard PCM (CD) format digital signals. VIDEO 2 DOLBY DIGITAL / PCM IN VIDEO 3 Remove the protection cap when using theVIDEO 3 jack. OPTICAL DIGITAL OUT (AUDIO) COAXIAL DIGITAL OUT (AUDIO) or Optical fiber cable Component with an Dolby Digital (or PCM) COAXIAL DIGITAL OUT Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See "Connecting video compo- nents".) Component with an Dolby Digital (or PCM) OPTICAL DIGITAL OUT Connect the video signal and analog audio signals to the VIDEO 3 jacks. (See "Connecting video compo- nents".) DOLBY DIGITAL RF OUT (AUDIO) RCA pincord COAXIAL DIGITAL OUT (AUDIO) OPTICAL DIGITAL OUT (AUDIO) LD player RF digital demodulator (DEM-9991D) (sold separately) PCM OUT To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D). Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver. Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See "Connecting video components".) If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section on the following page carefully. Setting up the system KRF-V8010D (En/T) Input mode settings The VIDEO2 and VIDEO3 inputs each include jacks for digital audio input and analog audio input. You must select beforehand which type of input is to be used for each connected component. The initial factory setting is to use the digital audio signal for playback. To use the analog audio input for playback instead (if, for example, you have connected a VCR to the VIDEO2 or VIDEO3 input), you must set the input mode for the corresponding input to the analog mode. After completing connections and turning on the receiver, follow the steps below. 1 Use the INPUT SELECTOR knob to select either VIDEO2 or VIDEO3. 2 Press the INPUT MODE key. Each press switches the setting as follows: 1 D-AUTO (digital input, auto sound) 2 D-MANUAL (digital input, manual sound) 3 ANALOG (analog input, manual sound) 4 DVD 6ch (this appears in the display only when set) When DVD 6ch is selected, you cannot use the SPEAKER B, BASS BOOST, MONITOR, SOURCE DIRECT, LISTEN MODE, SOUND, and SET UP keys.To use these keys, select an input mode other than DVD 6ch. Digital input: Select this setting to play digital signals from a DVD, CD, or LD player. Analog input: Select this setting to play analog signals from ...