Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
0 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source name associated with the MD/TAPE jacks to “MD,” follow the steps below: 1Use the INPUT SELECTOR knob to select .TAPE.. 2 Hold down the AUTO key for more than 2 seconds. • The source indication changes to “MD”. • To return to the original indication, repeat the above procedure. • You also will need to change the name input to the remote control to “MD”. RC1 Selecting the speaker system (except for KRF-V5030D/ V4530D) Press the SPEAKERS A or B key to select the speaker system to be used. A ON : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. A+B OFF : No sound from the speakers. Use this setting when listening with headphones for stereo sound and virtual surround in all playback modes. The indicator for the speakers you want to use should be lit. The speaker indicator lights. LSP A R SW B LSP A R SW B KRF-V7030D/V6030D KRF-V5030D/V4530D • Activating a surround mode or selecting “DVD/6ch” as the input source causes speaker system A to be selected automatically. On the KRF-V5030D/V4530D, press the SPEAKER key to switch the speakers on and off. Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/STANDBY keys. Operations Preparations • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable LSP A R 4Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: ____ feet (meters) Distance to center speaker: ____ feet (meters) Distance to surround speakers: ____ feet (meters) 2 Use the MULTI CONTROL to select the distance to the front speakers. The speaker indicator to be adjusted blinks. Indication in feet Indication in meters in 1 foot (0.3 m) increments. 3 Press the SET UP key. 4 Repeat steps 2 and 3 to input the distance for each of the speakers. 5 Setup is complete when the input indication reappears. SP R A L SW Display when all speakers have been selected. • The speakers you selected appear on the display. Confirm that all the speakers have been correctly selected. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, adjust the input level. 1Use the INPUT SELECTOR knob to select the source who.s input level you want to adjust. • You can store a separate input level for each input source. If the MONITOR function is on, you can store an input level for when MONITOR is on independently of the input levels for the input sources. 2Press the SOUND key several times until the .INPUT. indication appears. 3 Use the MULTI CONTROL to adjust the input level. LSP A R • The adjustment mode is displayed for approximately eight seconds. • The input level may be adjusted to any one of three settings: 0, -3, and -6. (The initial setting is 0.) 4 Press the SOUND key to return to the input indication. .. Normal playback Listening to a source component VOLUME CONTROL INPUT SELECTOR INPUT .. .. INPUT . SELECTOR SELECTOR VOLUME VOLUME RC-R0610 RC-R0510 .. 1Use the INPUT SELECTOR to select the source you want tolisten to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob KRF-V7030D 1 "PHONO" 2 "TUNER" 3 "CD/DVD" 4 "TAPE" or "MD" 5 "VIDEO1" 6 "VIDEO2" 7 "VIDEO3" 8 "DVD/6ch" 9 "AV AUX" KRF-V6030D/V5030D/V4530D 1 "PHONO" 2 "TUNER" 3 "CD/DVD" 4 "TAPE" or "MD" 5 "VIDEO1" 6 "VIDEO2" 7 "DVD/6ch" 2Start playback from the selected source. 3Use the VOLUME CONTROL knob (VOLUME keys) to adjustthe volume. Selecting VIDEO 2/MONITOR (except for KRF-V7030D) Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the “VIDEO 2” setting or the “MONITOR” setting, as appropriate. 8 Adjusting the sound MULTI CONTROL SOUND SOURCE DIRECT SPEAKERS A/B KRF-V6030D/.. V5030D/.. V4530D PHONES VOLUME CONTROL SOUND SOUND MULTI .... MULTI .. CONTROL CONTROL B.BOOST BASS BOOST MUTE MUTE VOLUME VOLUME RC-R0610 RC-R0510 Adjusting the tone You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. (Press the SOUND key once.) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice.) Operations SW LSP A R STEREO 2 Use the MULTI CONTROL to adjust the sound quality. • The bass and treble levels are adjustable from -10 to +10 in 2 step increments. • The adjustment item is displayed for approximately 8 seconds. Once-touch low frequency emphasis (bass boost) You can adjust the sound qualit...
Эта инструкция также подходит к моделям:Ресиверы и усилители - KRF-V4530D (688.64 kb)
Ресиверы и усилители - KRF-V5030D (688.64 kb)
Ресиверы и усилители - KRF-V7030D (688.64 kb)