Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Analog input: Select this setting to play analog signals from a cassette deck, VCR, or record player. Auto sound: In the auto sound mode (AUTO SOUND indicator lights), the receiver selects the listening mode automatically during playback to match the type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial factory setting is auto sound on. To keep the receiver set to the currently selected listening mode, use the INPUT MODE key to select “D-MANUAL” (manual sound). However, even when this setting is selected, there may be cases in which the listening mode is selected automatically to match a Dolby Digital source signal depending on the combination of listening mode and source signal. If the INPUT MODE key is pressed quickly, sound may not be produced. INPUT SELECTOR INPUT MODE VIDEO2/MONITOR PLAY INPLAY IN REC OUT AUDIO L R MD/TAPECD/DVDPHONO REC OUT L R AUX Cassette deck or MD recorder IN OUT Video component, 3 head cassette deck, or Graphic equalizer ™ IN OUT GND CD or DVD player OUT VIDEO2/MONITOR PLAY INPLAY IN REC OUT AUDIO L R MD/TAPECD/DVDPHONO REC OUT L R AUX Cassette deck or MD recorder IN OUT Video component, 3 head cassette deck, or Graphic equalizer ™ IN OUT GND CD or DVD player OUT Setting up the system Connecting audio components Shape of AC outlets Preparations SYSTEM CONTROL jacks % U.S.A. and Canada Other countries Australia 75.s AM 10kHz FM 100kHz 50.s AM 9kHz FM 50kHz DE- EMPHASIS CHANNEL SPACE To AC wall outlet (For VR-505/517/KRF-V5550D) Moving coil (MC) cartridge record player cannot be used directly from the receiver unit. It can only be used when another equalizer amplifier is connected. OUT Record player When you connect the audio cord of the video component to the VIDEO 2/MONITOR jacks, connect the video cord (yellow RCA pin cords) of the connected component to the VIDEO 2 IN jack. Setting up the system Connecting video components 11 Preparations 75.s AM 10kHz FM 100kHz 50.s AM 9kHz FM 50kHz EMPHASIS VIDEO 2 IN VIDEO MONITOR OUT VIDEO 1 OUT VIDEO 1 IN INCD/DVD DVD VIDEO 2/MONITOR AUDIO VIDEO 1 PLAY IN PLAY INREC OUT CD / DVD MD / TAPE PLAY INREC OUT DVD S VIDEO VIDEO 1 VIDEO 1 MONITOR OUT PLAY IN REC OUT PLAY IN IN Video inputs and outputs (Yellow RCA pin cords) Video deck Monitor TV OUT Audio inputs and outputs VIDEO IN DVD player or LD player IN OUT OUT OUT S Video jacks (VR-506/517/KRF-V6050D) Video inputs (Yellow RCA pin cords) About the S VIDEO jacks Use the S VIDEO jacks to make connections to video components with S VIDEO IN/OUT jacks. .If you use the S VIDEO jacks to connect your video playback components, be sure to use the S VIDEO jacks when connecting your monitor and video recording components. S VIDEO IN A video component with digital audio outputs should be connected to the VIDEO2 jacks. Setting up the system Connecting a DVD player (6-channel input) If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 9 Preparations DVD PLAY IN FRONT CENTER DVD SURROUND VIDEO 2/MONITORCOAXIAL SUB WOOFER DVD/6CH. INPUT VIDEO 2 IN VIDEO MONITOR OUT VIDEO 1 OUT VIDEO 1 IN CD/DVD DVD IN L R 75.s AM 10kHz FM 100kHz 50.s AM 9kHz FM 50kHz DEEMPHASIS CHANNEL SPACE FRONT OUT L/R S VIDEO OUT COAXIAL DIGITAL OUT (AUDIO) DVD player S VIDEO cord SURROUND OUT L/R VIDEO OUT (Yellow RCA pin cord) CENTER OUT SUBWOOFER OUT (Except for VR-505/KRF-V5550D) To switch the speakers off , press the MUTE key. CAUTION (Except for U.S.A. and Canada) Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard. • Do not place any objects impairing heat radiation onto the top of unit. • Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below. Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm CAUTION (For U.S.A. and Canada) Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard. • Do not place any objects impairing heat radiation onto the top of unit. Setting up the system Digital connections The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. 9 75.s AM 10kHz FM 100kHz 50.s AM 9kHz FM 50kHz DEEMPHASIS CHANNEL SPACE DVD VIDEO 2/MONITOR COAXIAL CD/DVD OPTICAL DIGITAL IN Preparations COAXIAL DIGITAL OUT (AUDIO) DOLBY DIGITAL RF OUT (AUDIO) Component with a DTS, Dolby Digital, or PCM COAXIAL DIGITAL OUT RF digital demodulator (DEM-9991D) (sold separately) Optical fiber cable PCM OUT OPTICAL DIGITAL OUT (AUDIO) CD player COAXIAL DIGITAL OUT (AUDIO) Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) ! LD player To connect an LD player with a DIGITAL RF OUT, connec...
Эта инструкция также подходит к моделям:Ресиверы и усилители - KRF-V5550D (2.92 mb)
Ресиверы и усилители - KRF-V6050D (2.92 mb)
Ресиверы и усилители - VR-505 (2.92 mb)
Ресиверы и усилители - VR-506 (2.92 mb)