Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
.For the operation when the power amplifier (KM-897) is connected to the KR-897, see 7 and refer to the instruction manual of the KM-897. SPEAKERS 3Adjust the volume. To decrease volume To increase volume VOLUME CONTROL DOWN UP PHONES 1Press the SPEAKERS key to OFF. 2Plug headphones. To mute sound temporarily MUTE Remote control unit only MUTE...ON Blinks To cancel Press the MUTE key again. Recording KR-897/KR-797 (En) When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTOR to select TAPE1 or MD according to the connected component. Preparation .Switch the TAPE1 display to MD or VIDEO1 with the following operation. 1Select TAPE1 with the INPUT SELECTOR. 2Press and hold the AUTO key for more than 2 seconds. 3VIDEO12MD1TAPE1 Each press switches the display. To record a music source 1Select the source to be recorded. INPUT SELECTOR Select an input source other than TAPE 1. 2Put the cassette deck in record-pause mode. 3Play the source and start recording. The input sources are switched in the following order: 1 TUNER (frequency display) 2 PHONO 3 TAPE1 (MD or VIDEO1) 4 CD 5 VIDEO2 .The VIDEO1 display can be switched to the display of other input by using the procedure described in “Preparation” above. .For the synchro recording with a cassette deck and/or MD recorder, refer to the respective instruction manuals.. .It is not possible the VIDEO1 or MD input to TAPE1 because all of these components should use the same INPUT SELECTOR position. Copying tape (Tape dubbing TAPE 2 = TAPE 1) Lights .For copying a tape using a double cassette deck, read the instruction manual of the double cassette deck. 2Select a source other than TAPE 1. TUNING BAND DISPLAY TAPE2 MONITOR INPUT SELECTOR CDTAPE 2 1Press the TAPE 2 MONITOR key. 3Play cassette deck 2 and start recording on cassette deck 1. Copying tape (Tape dubbing TAPE 1 = TAPE 2) 1Select TAPE 1 with the INPUT SELECTOR control of the main unit. 2Play the cassette deck connected to the TAPE 1 jacks and start recording of the cassette deck connected to the TAPE 2 jacks. Regarding TAPE 2 MONITOR A cassette deck or graphic equalizer can be connected to this unit’s TAPE 2 MONITOR terminals. If you connect a graphic equalizer, turn the TAPE 2 MONITOR key ON. If you connect a 3-head cassette deck, you can monitor the source sound, or the sound being recorded, while recording. Pressing the TAPE 2 MONITOR key lets you compare the recorded sound and the source sound. Refer to the operating manual for the component you connected for further details. Broadcast reception KR-897/KR-797 (En) 19 POWER PHONES ON/STANDBY UPDOWN 1 2 3 4 5 6 7 8 9 0 AUTO DIRECT MEMORY PRO LOGIC STEREO SRS 3D N.B. SOURCE DIRECT P.CALL 3 STEREO TUNING TAPE2 MONITOR POWER1 2 3 4 5 6 7 8 9 DISK SKIP 0 +10 SOUND CENTER MODE A/B +100 TUNER CD PHONO VIDEO2 MUTE 1 . 7 6 AV AUX REMOTE CONTROL UNIT RC-R0505 4 . 2 AUTO BAND P.CALL VOLUME CONTROL STANDBY SPEAKERS SRS 3D SPEAKERS INPUT SELECTOR VOLUME CONTROL +10 AUDIO-VIDEO SURROUND RECEIVER KR-897 BAND DIMMER VIDEO1 TAPE1 SETUP TAPE2 MONITOR LEVEL CONTROL LISTEN MODE : Keys or controls to be used in this operation Receiving broadcast stations 1 1 Select the TUNER input. INPUT SELECTOR Select the broadcast band.2TUNING BAND DISPLAY TAPE2 MONITOR AUTO FM MHz--8900. “AM” or “FM” indicator 3 3 Select the tuning method. Each press switches the turning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) AUTO MHz8900. . Usually, set the switch to AUTO (auto tuning). Lights Select manual tuning when noise interferes due to weak radio wave. (The stereo broadcasting is received in monaural during manual tuning.) 4 4 Select a station. AUTO DIRECT MEMORY TUNING BAND DISPLAY TAPE2 MONITOR To increase frequency To decrease frequency Frequency display “TUNED” lights up when a station is tuned. AUTO TUNEDFM MHz--8900. Auto tuning : The next station found is tuned automatically. Manual tuning : Press repeatedly or hold until a station is tuned. The input sources are switched in the following order: 1TUNER (frequency display) Frequency display 2PHONO 3TAPE1 (MD or VIDEO1)*1 4CD 8900 5VIDEO2 . MHz .The last frequency tuned before is displayed. .*1: How to switch the display *$ Each press switches the band as follows: 1 FM 2 AM .The same operation is also available with the 1 and . keys of the remote control unit. KR-897/KR-797 (En) : Keys or controls to be used in this operation POWER PHONES ON/STANDBY UPDOWN 1 2 3 4 5 6 7 8 9 0 AUTO DIRECT MEMORY PRO LOGIC STEREO SRS 3D N.B. SOURCE DIRECT P.CALL 3 STEREO TUNING TAPE2 MONITOR POWER1 2 3 4 5 6 7 8 9 DISK SKIP 0 +10 SOUND CENTER MODE A/B +100 TUNER CD PHONO VIDEO2 MUTE 1 . 7 6 AV AUX REMOTE CONTROL UNIT RC-R0505 4 . 2 AUTO BAND P.CALL VOLUME CONTROL STANDBY SPEAKERS SRS 3D SPEAKERS INPUT SELECTOR VOLUME CONTROL +10 AUDIO-VIDEO SURROUND RECEIVER KR-897 BAND DIMMER VIDEO1 TAPE1 SETUP TAPE2 MONITOR LEVEL CONTROL LISTEN MODE Receiving radio stations by speci...
Эта инструкция также подходит к моделям:Ресиверы и усилители - KR-897 (1.31 mb)