Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note Some speaker setup items may appear dimmed in the display. This means that they have been adjusted automatically due to other speaker settings or may not be adjustable. 4 Turn –/+ to select the setting you want. The setting is entered automatically. Note Press ENTER if you select the setting for “SP. PATTERN X–X”. 5 Repeat steps 3 and 4 until you have set all of the items that follow. Speaker setup parameters The initial settings are underlined. x EASY SET UP XXX (Speaker easy setup) •YES If you want to set up your speakers automatically, select “YES”. You can select a pre-defined speaker pattern (see the supplied “Easy Setup Guide”). •NO If you want to adjust the settings of each speaker manually, select “NO”. x SP. PATTERN X–X (Speaker setup pattern) When you select “EASY SET UP YES”, select the speaker setup pattern. Turn –/+ to select the speaker setup pattern and press ENTER to enter the selection. Check your speaker pattern using the supplied “Easy Setup Guide”. x SUB WOOFER XXX (Sub woofer selection) •YES If you connect a sub woofer, select “YES”. •NO If you did not connect a sub woofer, select “NO”. The front speakers are automatically set to “LARGE” and you cannot change this setting. This activates the bass redirection circuitry and outputs the LFE signals from other speakers. • In order to take full advantage of the Dolby Digital bass redirection circuitry, we recommend that you set the cut off frequency on the sub woofer as high as possible. x FRONT SP XXXXX (Front speakers size) •LARGE If you connect large speakers that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. •SMALL If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the front channel bass frequencies from the sub woofer. When the front speakers are set to “SMALL”, the center, surround and surround back speakers are also automatically set to “SMALL” (unless previously set to “NO”). x CTR SP XXXXX (Center speaker size) •LARGE If you connect a large speaker that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the center speaker to “LARGE”. •SMALL If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the center channel bass frequencies from the front speakers (if set to “LARGE”) or sub woofer.a) Getting Started continued 17GB •NO If you did not connect a center speaker, select “NO”. The sound of the center channel will be output from the front speakers.b) x SURR SP XXXXX (Surround speakers size) • LARGE If you connect large speakers that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the surround speakers to “LARGE”. •SMALL If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the surround channel bass frequencies from the sub woofer or other “LARGE” speakers. •NO If you did not connect surround speakers, select “NO”.c) x SB SP XXXXXX (Surround back speakers selection) When the surround speakers are set to “NO”, the surround back speakers are also automatically set to “NO” and the setting cannot be changed. • DUAL If you connect two surround back speakers, select “DUAL”. The sound will be output to a maximum of 7.1 channels. • SINGLE If you connect only one surround back speaker, select “SINGLE”. The sound will be output to a maximum of 6.1 channels. •NO If you did not connect surround back speaker, select “NO”. Tips • a)–c) correspond to the following Dolby Pro Logic modes a) NORMAL b) PHANTOM c) 3 STEREO • The “LARGE” and “SMALL” settings for each speaker determine whether the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel, the bass redirection circuitry sends the corresponding bass frequencies to the sub woofer or other “LARGE” speakers. However, since bass sounds have a certain amount of directionality, it is best not to cut them, if possible. Therefore, even when using small speakers, you can set them to “LARGE” if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to “SMALL”. If the overall sound level is lower than you prefer, set all speakers to “LARGE”. If there is not enough bass, you can use the BASS parameter in the EQUALIZER menu to boost the bass levels. To adjust the bass, see page 36. x FRONT DIST. X.X m (Front speaker distance) Initial setting: 3.0 m Lets you set the distance from your listening position to the front speake...