Оценок - 3, средний балл: 3.7
(
)
)
|
Фото и характеристики Sony STR-DA5200ES |
К этому устройству также есть другие инструкции:
Ресиверы и усилители - STR-DA5200ES (6.3 mb)
Ресиверы и усилители - STR-DA5200ES (19.3 mb)
Ресиверы и усилители - STR-DA5200ES (29.01 mb)
Фрагмент инструкции
Connecting components with multi-channel output jacks DVD player, Super Audio CD player, etc. A B AAudio cord (not supplied) BMonaural audio cord (not supplied) 25GB Getting Started The following illustration shows how to connect a component with analog jacks, such as tape deck, turntable, etc. Note If your turntable has a ground (earth) wire, connect it to the (U) SIGNAL GND terminal. Connecting components with analog audio jacks Super Audio CD player, CD player Tape deck Turntable A MD deck, DAT deck A AAudio cord (not supplied) A A 4b: Connecting the video components How to hook up your components This section describes how to hook up your components to this receiver. Before you begin, refer to “Component to be connected” below for the pages which describe how to connect each component. After hooking up all your components, proceed to “5: Connecting the antennas (aerials)” (page 35). Component to be connected Page TV monitor 19, 31 With HDMI jack 27 DVD player, DVD recorder 29-30 Satellite tuner 31 VCR 32 Camcorder, video game, etc. 32 Video input/output jacks to be connected The image quality depends on the connecting jack. Refer to the illustration that follows. Select the connection according to the jacks on your components. Digital Analog High quality image 26GB 27GB Getting Started HDMI is the abbreviated name for High- Definition Multimedia Interface. It is an interface which transmits video and audio signals in digital format. HDMI features • A digital audio signals transmitted by HDMI can be output from the speakers and the PRE OUT jacks on this receiver. This signal supports Dolby Digital, DTS, and linear PCM. • Linear PCM (sampling frequency less than 192 kHz) with digital audio signals of up to 8 channels can be received with this receiver using the HDMI jack. • Analog video signals input to the VIDEO jack, S VIDEO jack, or COMPONENT VIDEO jacks can be output as HDMI signals. Audio signals are not output from an HDMI OUT jack when the image is converted. Connecting components with HDMI jacks DVD player Satellite tuner Blu-ray Disc player, hard disk recorder A A A AHDMI cable (not supplied) We recommend that you use a Sony HDMI cable. Audio/video signals Audio/video signals Audio/video signals TV monitor, projector, etc. Audio/video signals continued Notes on HDMI connections • Use an HDMI cable with the HDMI logo (made by Sony). • Check the setup of the connected component if an image is poor or the sound does not come out of a component connected via the HDMI cable. • An audio signal input to the HDMI IN jack is output from the speaker output jacks, HDMI OUT jack and PRE OUT jacks. It is not output from any other audio jacks. • A video signal input to the HDMI IN jack can only be output from the HDMI OUT jack. The video input cannot be output from the VIDEO OUT jacks, S VIDEO OUT jacks, or MONITOR OUT jacks. • The audio and video signals of HDMI input are not output from the HDMI OUT jack while the receiver menu is displayed. • When you want to listen to the sound from the TV speaker, set “HDMI Audio” to “TV+AMP” in the Audio settings menu (page 55). If set to “AMP,” the sound is not out put from the TV speaker or you cannot play back multi-channel software. • The multi/stereo area audio signals of a Super Audio CD are not output. • Be sure to turn on the receiver when video and audio signals of a playback component are being output to a TV through this receiver. Unless the power is on, neither video nor audio signals will be transmitted. • Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. Check the setup of the connected component if an image is poor or the sound does not come out of a component connected via the HDMI cable. • Sound may be interrupted when the sampling frequency or the number of channels of audio output signals from the playback component is switched. • When the connected component is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI OUT jack may be distorted or may be not output. In this case, check the specification of the connected component. • Refer to the operating instructions of each component connected for details. • We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D component, the sound and/or the image may not be output. Connect other audio cords or digital connecting cords, then set “Input Assign” in the Input menu (page 90) when the sound is not output correctly. 28GB 29GB Getting Started The following illustration shows how to connect a DVD player/DVD recorder. It is not necessary to connect all the cables. Connect audio and video cords according to the jacks of your components. Note To output multi-channel digital audio, set the digital audio output setting on the DVD player. Refer to the operating instructions supplied with the DVD player. Connecting a DVD player Connecti...