Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Both mono and stereo inputs are available. Digital Multi Equalizer Power amplifier Speakers Video sound Microphone for a host Microphone on the platform 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 MONO POWER 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 4 4 2 2 8 8 100 100 6 6 ST MULTI IN 4 2 8 100 6 SUB OUTSTEREO MONO STEREO OUT INPUT REAK LINE IN SUB 4 2 8 100 6 MONO OUT Audio Mixer WR-XS3 Any mono and stereo input can be assigned to the SUB OUTPUT jack. To adjust the output levels Mono and stereo outputs are individually adjustable. In the case shown in the figure, the volume of microphones is adjusted with the MONO OUT knob and that of stereo source devices is adjusted with the STEREO OUT knob. DIP switch setting Switch A is set to ON and Switch B is set to OFF. ON OFF Switch B Switch A . Mode 3 The signals from stereo or mono input lines are separately output through the STEREO OUTPUT, MONO OUTPUT and SUB OUTPUT jack. For example, this connection is used for zone amplification in a shop. • The signals from the MONO INPUT 1 and 2 connectors are output through the STEREO OUTPUT and MONO OUTPUT jacks. (Input for all-call broadcasting in any zone) • The signals from the MONO INPUT 3 connector are output through the STEREO OUTPUT jack (Zone 1) and the signals from MONO INPUT 4 connector are output through the MONO OUTPUT jack (Zone 2). (Input for broadcasting in each zone) • The signals from the STEREO INPUT 1 to 4 jacks are output through the STEREO OUTPUT (Zone 1) and MONO OUTPUT (Zone 2) jack. • Amplification in other areas is possible by assigning another BGM to the SUB OUTPUT jack and mixing with all-call broadcasting. • The signals from the MULTI INPUT ST jack or MULTI INPUT MONO connector are output to the STEREO OUTPUT, MONO OUTPUT and SUB OUTPUT jacks.* *The output line is assigned with the assign button setting. (Refer to p. 19.) Wireless microphone Mono output is also available in Zone 1. (Switch inside) Zone 2 Zone 1 Zone 2 Wireless microphone Wireless microphone MD CD TAPE MONO INPUT 1 to 4 STEREO INPUT 1 to 4 MONO 1 to 2 (Zone 1 and 2) MONO3 Digital Multi Equalizer Power amplifier Speakers Video soundMicrophone on the platform Microphone for a host Antenna for wireless microphone Diversity wireless receiver in the hall 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 MONO POWER 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 4 4 2 2 8 8 100 100 6 6 ST MULTI IN 4 2 8 100 6 SUB OUTSTEREO MONO STEREO OUT INPUT REAK LINE IN SUB 4 2 8 100 6 MONO OUT Audio Mixer WR-XS3 Any mono and stereo input can be assigned to the SUB OUTPUT jack as Zone 3 (Zone 1) MONO4 (Zone 2) To adjust the output levels Requires setting of an internal switch. In the case shown in the figure, the volume of Zone 1 is adjusted with the STEREO OUT knob ,and that of Zone 2 is adjust ed with the MONO OUT knob. To output the mono mix signal (the same signal through the STEREO OUTPUT jack) ON The internal switch setting is necessary. Refer to a service manual procurable in your area. DIP switch setting OFF Switches A and B are set to OFF. Switch A Switch B ¦ Input Line Setting for SUB OUTPUT The SUB OUTPUT jack at the rear panel can output any signal from the STEREO INPUT 1 to 4 jacks or MONO INPUT 1 to 4 connectors. The output setting is determined with the DIP switch setting. The input signal from the LINE IN jack, MULTI INPUT ST jacks or MULTI INPUT MONO is also assignable to the SUB OUTPUT jack. The output setting is determined with the assign button setting at the front panel. Refer to p. 19. Any output can be assigned. Both mono and stereo inputs are available. 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 MONO POWER 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 4 4 2 2 8 8 100 100 6 6 ST MULTI IN 4 2 8 100 6 SUB OUTSTEREO MONO STEREO OUT INPUT REAK LINE IN SUB 4 2 8 100 6 MONO OUT Audio Mixer WR-XS3 . DIP switch setting The input line is assigned to the SUB OUTPUT jack by setting Switches MONO 1 to 4 and STEREO 1 to 4. When all DIP switches are set to ON, the associated input signal is assigned to the SUB OUTPUT jack. More than one input line is selectable. ON OFF STEREO MONO 12341234 INPUT SELECT The figure shows an example that assigns the MONO INPUT 3 connector, STEREO INPUT 2 jack, and STEREO INPUT 4 jack to the SUB OUTPUT jack. ¦ Output Line Setting for MULTI IN/LINE IN The signal from the MULTI IN ST jacks and MULTI IN MONO connector at the rear panel can be output through any of the STEREO OUT, MONO OUT and SUB OUTPUT jacks The output connector is assigned with the assign switches at the front panel. The LINE IN jack at the front panel is also usable as a multiple input connector. 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 MONO POWER 4 2 8 100 1 6 4 2 8 100 2 6 4 2 8 100 3 6 4 2 8 100 4 6 4 4 2 2 8 8 100 100 6 6 ST MULTI IN 4 2 8 100 6 SUB OUTSTEREO MONO STEREO OUT INPUT REAK LINE IN SUB 4 2 8 100 6 MONO OUT Audio Mixer WR-XS3 Any output can be assign...