Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Send the command [?] and receive the following feedback: [(MT101-102U0)(MT113-100C04)] MT101-102U1 = Panel Number and Unit ID MT113-100C04 = An MT113-100 is in slot 4. 5. [?C] This command will return general information about the card and its status. It is a function of both the card and the front panel and is only available with MultiTasker Front Panel systems that have the following firmware: 400-0209-002 10 MULTITASKER™ 690-0122-015 = Version 015 or later. 690-0123-004 = Version 004 or later. 690-0124-018 = Version 018 or later. NOTE: In MTSetup™, send the command [VER] from the Terminal Window. The system will respond with feedback similar to the following: [690-0122-015 690-0123-004 690-0124-018] Check the last three digits against the numbers above to determine if the option is available. Command Format: [?CnUi] Cn = Card ID (n = # from 1 to max slots) Ui = Unit ID (i= from 0 to 9) The MT113-100/101 is in slot #4. Send the command [?C4] to receive the feedback status. All status feedback is enclosed in brackets, “[ ]“. Each data field within the status is enclosed in parentheses. The first two characters identify the status type. The last three characters are the card’s ID. [(MT113-100C04)(VR690-0133-009C04) (VO16C04)(VI161616C04)(VB08C04) (VT08C04)(VL01C04)(VM0C04)] MT113-100 = Card Type VR690-0133-009 = Firmware version VO16 = Output Volume Level=16 VI161616 = Input volume levels VB08 = Bass level = 08 out of 16 VT08 = Treble level = 08 out of 16 VL01 = Loudness (00=ON, 01=OFF) VM0 = Mute (0=OFF, 1=ON) The Input Volume status line is read from left to right as outputs one through three. Each volume level is 2 digits, in this case, each is set to 16. 6. [STA] This command enables/disables automatic feedback from the front panel. The command affects any card with auto-feedback capability, not just the MT113-100/101. The default at power on or reset is STA0, OFF. Command Format [STA1] = ON Command Format [STA0] = OFF Feedback Prefix Definitions: VR = Firmware Version VO = Output Volume VI = Input Volume VB = Bass Volume VT = Treble Control VL = Loudness Control VM = Mute Control Example: Command = [VLOA12C04] Feedback = (VO12C04) VO = Output Volume 12 = Output volume level12 C04 = Card slot number 7. […S] – SAVE This command will save the configuration command being sent in memory. When sending the command [VLBA12C4S], after reset or power up, the bass level on C4 will be 12 out of 16. 8. […F] – FEEDBACK After processing a command, an OK or ER will be returned as feedback if "F" is included at the end of some command strings. 9. [ + ] and [ -] These commands allow a selected property to be adjusted from keyboard commands or programmed front panel buttons. Command Format: [ + ], [ -] [+] = Increment level by one step [-] = Decrement level by one step 400-0209-002 11 MULTITASKER™ Example: Select the Output Volume command for the card in slot #4. The current Output Volume level is 10, but it is not the optimal value. After sending the following commands, an optimum volume level of 15 is obtained: 1. [SELOC4] The current volume level is 10. 2. [ – ] [ – ] [ – ] The level is now 7 and is too low. 3. [+][+][+][+][+][+][+][+] The level is now 15 and no further adjustments are required. 10. [SELI] This command sets the path to adjust the INPUT volume level. The input volume range is 00 to 16 and is adjustable using the [+] and [-] commands. Command Format: [SELImCnUi] m = Input (m = # from 1 to 3) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: An MT113-100/101 is in slot #4. Adjust the volume on Input 2 by sending the command [SELI2C4] and then using the [+] and [-] commands. 11. [SELO] This command sets the path to adjust the OUTPUT volume level. The output volume range is 00 to 16 and is adjustable using the [+] and [-] commands or the Volume Ramping commands. Command Format: [SELOCnUi] Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example 1: An MT113-100/101 is in slot #4. Adjust the output volume by sending the command [SELOC4] and then using the [+] and [-] commands. Example 2: The output volume may also be adjusted using key ramping commands. See the VOLUME RAMPING FEATURE section of this manual for details on using this feature. 12. [SELB] This command sets the path to adjust the bass level. The BASS level range is 00 to 16 and is adjustable using the [+] and [-] commands. Command Format: [SELBCnUi] Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: An MT113-100/101 is in slot #4. Adjust the BASS on the output by sending the command [SELBC4] and then using the [+] and [-] commands. 13. [SELT] This command sets the path to adjust the treble level. The TREBLE level range is 00 to 16 and is adjustable using the [+] and [-] commands. Command Format: [SELTCnUi] Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: An MT113-100/101 is in slot #4. Adjust the TREBLE o...
Эта инструкция также подходит к моделям:Ресиверы и усилители - MT113-101 (522.4 kb)