Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
To do this, press TAPE. Switching this button in/out allows an A/B comparison between the source signal and the recorded signal. Setting up your A80 amplifier The A80 allows you to adjust listening settings to suit your taste, and to customise various features of the amplifier to fit your system. Use this diagram to help you navigate through the settings available. The ENTER and SELECT buttons are represented in the diagram by the symbols and respectively. The Control knob is shown as . Adjusting listening settings The default display mode is VOLUME, where the Control knob is used to adjust sound level. Press SELECT to enter edit mode and cycle through the other settings: BALANCE, VOL RES, I/P trims, etc. When a setting is selected, press SELECT again and adjust it with the control knob. Press ENTER to fix the change you have made and return to idle (volume) mode. Menu map AdjustARCAM A80 (‘Switch on’ state) volumeBALANCEvol resi/p trimsproc moderec outputmax on volreset0 ... 72(dB) ResetMax On VolRec OutputProc ModeI/P TrimsVol ResBalanceAdjustAdjustL | RAdjustAdjustAdjustAdjustAdjustRES REFRES FINERES STDCD TRM 0PROC AVFIXED 1... AV, PHONO, CD, TUNER, AUX, DVDONVOL OFFONVOL 1... NO RESETYES RESET Balance – Once selected, use the Control knob to shift the balance between Left and Right channels. Volume Resolution – RES REF, RES FINE or RES STD. ‘Fine’ and ‘Standard’ represent different levels of volume control sensitivity. The ‘Reference’ setting gives absolute increments in 0.5dB steps. Input Trims – use the source select buttons and Control knob to set input trims for each source. Input trims are used to compensate for variations in output levels of different source equipment. Processor Mode – This mode enables you to adjust the gain of the amplifier. The amplifier can then be used to drive the front left and right speakers in a surround sound system when fed from a separate processor. You can then control the volume of the entire system using the processor, feeding the sound into the TAPE input. Set the gain to match the amplifiers that drive your other loudspeakers. Recording Output – This allows you to select the source signal for recording: AV, PHONO, CD, TUNER, AUX or DVD. Maximum ‘On’ Volume – Use the Control knob to adjust the volume setting at switch-on. ONVOL OFF indicates that the feature is not activated. ONVOL 1 (or higher) sets the volume at start-up (in dB). Reset – this restores all amplifier settings, including input trims, to their factory defaults. Using the remote control CR-389 Remote Control The CR-389 remote control gives access to all functions available on the front panel of the A80. It also has controls to operate Arcam CD players, AM/FM tuners and DAB tuners. The remote control transmits Philips RC-5 type codes. TUNER These buttons are used to control tuner functions. Note that the FM/DAB lights indicate into which mode you are switching the remote control. The lights only illuminate for five seconds to conserve battery power. If neither light is illuminated this does not mean that the remote control is not working! FMDABPROGINFORPTMODEBAND1-92-103-11FMDABSELECTTUNERCR-389CDAMPLIFIERVCRDVDTAPEAVTUNERCDAUXPHONOENTERSP1SP2DISPMENUDISP4-125-136-147-158-16 Power/Standby Toggles the amplifier between standby mode and full power mode. The power indicator light next to the power button on the front panel is red if the amplifier is in standby, amber while the amplifier is powering up (this only takes a few seconds) and green when the amplifier is powered up. (UP and DOWN) These buttons do not apply to the A80. SP1 and SP2 These buttons allow you to select and deselect the main (SP1) and secondary (SP2) sets of speakers attached to your amplifier (see page 6). ENTER Performs the same function as the ENTER button on the front panel (see page 8). DISP (display) Cycles through the settings ‘Bright’, ‘Off’ and ‘Dim’. Turning the display ‘Off’ generally gives a slight improvement in sound quality. SELECT Performs same function as the SELECT button on the front panel. It allows you to use the remote’s volume switch in the same way you use the control dial on the front panel – to adjust various amplifier settings (see page 8). Note that pressing + corresponds to turning theControl knob clockwise, – to anticlockwise. Volume and (mute) Press + to increase volume or – to decrease the output volume of the amplifier. Press to mute the speaker connections and preamp outputs. Both tape outputs and the headphone socket remain active. Mute is disabled either by pressing again, or by adjusting the volume. You can use the remote’s volume control in conjunction with the SELECT button to adjust balance, tone and amplifier settings. Source selection buttons These operate in the same way as the source selectors on the front panel of your integrated amplifier. CD controls These offer basic controls of Arcam CD players NOTE: Remember to install the two supplied AAA batteries before trying to use your remote con...
Эта инструкция также подходит к моделям:Ресиверы и усилители - P80 (3.39 mb)
Ресиверы и усилители - A80 (3.39 mb)
Ресиверы и усилители - P80 (3.39 mb)