Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
For a more detailed explanation of the Release Edit Group function, see pages 44 and 45. Remember, if you want to keep the edited program, be sure to store it to one of the User locations. For instructions on how to do this, turn to page 38. 3 3 Basics of Equalization Basic operation: Store mode Once you have created a program you would like to save, press the [STORE] button to enter Store mode. This will cause the Numeric LED Display to blink with the number of the current program. If you were on a Preset program while editing, you will not be able to store the program until you select one of the 30 User program locations as its destination. To do this, use the [DOWN/UP] buttons. If you press the [UP] button first, you will see the Numeric LED Display jump to User program 30, which is the first available User program location. If you press the [DOWN] button first, you will see the Numeric LED Display jump to User program 59, which is the highest-numbered User program location available. If you were already on a User program when you entered Store mode, then using the [DOWN/UP] buttons will call up the next User program. Once you are in the User program area inside Store mode, pressingthe [DOWN/UP] buttons allows you to choose a program number between 30-59 as the destination for your edited program. Pressing and holding one of these buttons will cause the unit toscroll progressively faster through the available choices. If you're holding the [DOWN] button, when the unit reaches User program 30 it will "wrap" around to number 59 and continue scrolling downward. Pressing and holding the [UP] button will cause the numbers to scroll in the opposite direction, wrapping from program 59 to program 30 and continuing upward. As in Program mode, there's an even faster way to select the destination program location. If you press and hold the [DOWN] button and then push the [UP] button, the unit will jump toProgram 30. If you continue pressing the [UP] button, the DEQ230 will jump forward through the User locations inincrements of 10 (40, 50, 30, 40, 50, etc.). Similarly, if you press and hold the [UP] button and then push the [DOWN] button, the unit will jump to Program 30. If you continue pressing the [DOWN] button, the DEQ230 will jump backward through the User locations in increments of 10 (50, 40, 30, 50, 40, 30, etc.). Once you have chosen the location you want, press the [STORE] button again. This will store the program into the user locationyou selected. Remember, if at any time you decide you do not want to save theedited program, simply press the [LINK/EXIT] button to return to Program mode. Your edited program will still be there, as evidenced by the dot on the right side of the Numeric LEDDisplay. The “destination” program will not have beenoverwritten. 38 Basics of Equalization 3 Channel Copy You can use the Link function while editing to help set up identical curves on both channels. But at some point the curves may needto diverge slightly (or significantly). Rather than unlinking the channels and starting all over again on Channel B, we haveincluded a handy feature called Channel Copy as a subset of Storemode. The Channel Copy feature is a real time-saver. It will allow the settings from Channel A to be stored over whatever settings are inChannel B, so that after the completion of the Store process there will be no difference between the settings of Channels A and B for that program. Then you can begin to diversify the settings of thechannels to match the needs of the incoming audio. The process is simple, but it is subtly different from the normalStore procedure. Pay close attention to the following steps: 1. Before storing the program, unlink the channels. That wayyou’ll be able to begin editing Channels A and B independently as soon as you complete step 7. 2. Press and hold the [STORE] button to enter Store mode. The Numeric LED Display will begin to flash. 3. While holding the [STORE] button, press the [LINK/EXIT] button. This will cause the Link LED to begin flashing also. 4. Release both buttons. 5. Select the location for the new program using the methods described on the previous page. 6. To abort the Store procedure, press the [LINK/EXIT] button. The settings for Channel A will not have been copied over to Channel B. 7. To store the program, press the [STORE] button a second time. The settings for Channel A will have been duplicated onChannel B. To confirm this, toggle the [LINK/EXIT] button. You should see no difference between the settings ofthe channels. Even the Channel Level settings of Channel B should match that of Channel A. 3 3 Basics of Equalization Basic operation: Audition mode No doubt there will be times when you want to switch back and forth between different programs to determine which one is best suited for the audio source. But as easy as it is to navigate betweenthe DEQ230's programs in Program mode, it's still difficult tofocus on what's happening to the audio when you're ma...
Эта инструкция также подходит к моделям:Ресиверы и усилители - DEQ230 (952.85 kb)