Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
7. Range Switch -When depressed, this switch will multiply the selected crossover frequency by 10.The LED will light indicating that the markings on the Frequency knob (6) should be multiplied by 10. 8. Channel 2 Gain -This is the input level for Channel 2 in Stereo mode. In Mono mode this knob has no function. 9. Low/Mid Level -This knob controls the volume for the Channel 2 low frequency output in Stereo mode, and the mid-range frequency output volume in Mono mode. 10. High Level -This knob controls the volume for the Channel 2 high frequency output in Stereo mode, and the high frequency output in Mono mode. 11. Frequency -This knob sets the crossover frequency separating the mids from the highs in Mono mode, and the lows from the highs for Channel 2 in Stereo mode. 12. Range Switch -When depressed, this switch will multiply the selected crossover frequency by 10.The LED will light indicating that the markings on the Frequency knob (11) should be multiplied by 10. SR835 Crossover REAR PANEL HIGH BAL. HIGH BAL. HIGH UNBAL. HIGH UNBAL. LOW BAL. MID BAL. LOW UNBAL. MID UNBAL. INPUT HIGH BAL. HIGH UNBAL. LOW BAL. LOW BAL. LOW UNBAL. LOW UNBAL. INPUTSTEREO MONO AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR WARNING: SHOCK HAZARD-DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE BACK. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CHANNEL 2 CHANNEL 1 LOW SUM OUT 120 V DOD Professional Products STEREO MONO 60 Hz 50 Hz100 V OR 18 WATTSSandy,Utah U.S.A. 1234 5678910 11 12 1. High Bal -This is a TRS balanced output for the high frequencies in both Mono mode and Channel 2 in Stereo mode. 2. High Unbal -This is an unbalanced out put for the high frequencies in both Mono mode and Channel 2 in Stereo mode. 3. Low/Mid Bal -This is a TRS balanced low frequency output for Channel 2 in Stereo mode and a TRS balanced mid range frequency output in Mono mode. 4. Low/Mid Unbal -This is an unbalanced low frequency output for Channel 2 in Stereo mode and an unbalanced mid range frequency output in Mono mode. 5.Channel 2 Input -This is a TRS balanced input for Channel 2 in stereo mode. This jack has no function in Mono mode. 6. Low Sum Output -This is a mono output containing the sum of Channel 1 and Channel 2 low frequencies. 7. High Bal -This is a TRS balanced high frequency output for Channel 1 in Stereo mode.This jack has no function in Mono mode. 8. High Unbal -This is an unbalanced high frequency output for Channel 1 in Stereo mode.This jack has no function in Mono mode. 9.Low Bal -This is a TRS balanced low frequency output in both Mono mode and Channel 1 in Stereo mode. 10. Low Bal -This is an unbalanced low frequency output in both Mono mode and Channel 1 in Stereo mode. 11. Channel 1 Input -This is a TRS balanced input for Channel 1 in stereo mode and the master input in mono mode. 12. Power Receptacle -Connect the provided power cord from this receptacle to an AC outlet. 3 4 SR835 Crossover INSTALLATION Install the crossover in a rack with the provided rack screws. Route the AC power cord to a convenient power outlet away from audio lines. The unit may be turned on and off using the front panel power switch. Since the units draw a relatively small amount of current during idle, they can be left on continuously. DOD crossovers generate very little heat during operation and thus do not need to be specially ventilated or cooled. The units should not, however, be subjected to high temperatures for extended periods. Although the unit's chassis is shielded against radio frequency and electromagnetic interference, extremely high RF and EMI fields should be avoided. ATTENTION: Use only one Channel output connector for each frequency range at a time. Using the balanced and unbalanced outputs for the same frequency range at the same time can unbalance balanced lines, cause phase cancellation, short a conductor to ground, or cause damage to other equipment connected to the crossover. FOR BALANCED 1/4 “ TRS PHONE PLUG CONNECTION - Wire the connectors as follows: Phone Plug Connection tip : high ring : low sleeve : ground FOR 1/4" MONO PHONE PLUG CONNECTION: Phone Plug Connection tip : high sleeve : ground Once the crossover has been installed and adjusted for the required cross frequencies, and levels, an optional security panel can be installed to keep unauthorized persons from changing settings. SR835 Crossover 5 BI-AMP APPLICATIONS For bi amp applications, the SR835 must be set to the Stereo mode regardless of whether you are running in stereo or mono. The Stereo mode configures the SR835 as two individual channels, each providing a two way split. If you are running your sound system in stereo, both channels would be used: one for the left, and one for the right. If you are running in mono, only one of these channels would be used but the SR835 would still be set to Stere...