Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Alternatively, you can use this input for other (line level) equipment such as a CD player, tuner, etc., (but not a turntable). DVD bl – Connect this input to the stereo audio outputs of a DVD player. AV bm – Connect this input to the stereo audio outputs of audio visual equipment such as a laserdisc player, satellite or Nicam tuner. TUNER bn – Connect this input to the audio outputs of your radio tuner. CD bo – Connect this input to the audio outputs of your CD player or DAC (digital to analogue converter). AUX bp – As the C30 has the phono board fitted as standard, the AUX connection is a line level output carrying an equalised phono signal. If desired, this output can be connected to a recording device. Should you wish to remove the phono board, then the AUX connections can be used as a line input. Please see your dealer for further information about this option, as removing the phono board yourself may invalidate the warranty. PHONO bq – Connect this input to the audio outputs of your turntable. The phono module supplied with the C30 is compatible with most moving magnet and moving coil cartridges. Set the blue switch immediately below these connections to the correct setting, as follows: MM – is used for high output moving coil and all moving magnet cartridges. The blue switch is flush with the rear panel of the C30. MC – is used for low output moving coil cartridges. The blue switch is depressed inside the rear panel of the C30. Phono earth terminal – For connecting your turntable earth lead (if fitted). Note that this terminal must not be used as a safety earth. TRIG OUT and REMOTE IN 3 (12V in and out) – These connections are intended for use in multi-room installations. TRIG OUT – This output provides a 12V signal whenever the unit is switched on (i.e., not off or in standby). This signal can be used to switch on automatically power amplifiers (or other equipment) connected to the C30, as they will come on when the C30 is activated. This is useful if the power amplifier is remote from the C30, or otherwise difficult to access. This feature can be used with both the P35 and the P1. If you are bi-amping with a power amplifier and wish to power both units on or off simultaneously, see page 11. REMOTE IN – This allows remote control signals to be received by the C30 if the remote sensor is covered (or otherwise not ‘visible’ to the remote control). An external sensor is used to receive the signals from the remote control, which are then fed to the C30 (into this input) using a suitable cable. Remote control signals acceptable to the C30 must be in modulated RC5 format, with a voltage level of between 5V and 15V. Note that in normal use there is no need to make any connections to these sockets. If you would like to make use of these features, please contact your dealer for more advice on how to make the connections and on what type of cable to use. Using your C30 pre-amplifier C30 PRE-AMPLIFIERMUTEDISPLAYPOWERPHONESPHONO/AUXCDTUNERAVDVDVCRTAPETONEENTERMODERECORDSELECT FRONT PANEL CONTROLS This section describes how to operate your amplifier. If your amplifier has not been installed for you, you should first read the section ‘Installation: C30 pre-amplifier’ on page 5. POWER bn Switches the unit on and off. The power indicator light (directly above the switch) shows the status of the amplifier. A red light means the amplifier is in stand-by mode (press the POWER/STANDBY button on the remote control, or the POWER button on the front panel, to switch between stand-by and powered-up modes). Remote control receiver 1 The remote control’s infrared receiver is positioned behind the ‘FMJ’ badge. Ensure the receiver is in a clear line of sight from the remote control to allow signals to be received. MODE 2, UP and DOWN 5 These buttons are intended for use with any future optional modules that may become available for the C30. The UP and DOWN buttons, however, are used with the existing C30 pre-amplifier to move the cursor when customising the ‘Welcome message’ (see page 9). Control knob 7, SELECT 4 and ENTER 6 The control knob has two functions: . as a volume control, to adjust the output of the headphones and of the pre-amp output (PRE OUT). . when used in conjunction with the SELECT and ENTER buttons, to customise amplifier settings (see page 9). VOLUME CONTROL SETTINGS It is important to realise that volume level shown on the display is not an accurate indication of the power delivered to your loudspeakers. The amplifier often delivers its full power long before the volume control reaches its maximum position, particularly when listening to heavily recorded compact discs. However the amplifier also has to be capable of giving full power output from much lower level sources, such as tuners and cassette decks. Using these sources, the volume control setting may be much higher before distortion (audible overload) sets in. It is possible to compensate for these input level differences by using the ‘Input trims’ m...
Эта инструкция также подходит к моделям:Ресиверы и усилители - C30, P35, P1 (2.87 mb)
Ресиверы и усилители - C30, P35 (2.87 mb)
Ресиверы и усилители - C30, P35, P1 (2.87 mb)