Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
950 •EN60950 •CE •– EN55022 Class B •– EN50082-1 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) • and the Low Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these directives implies conformity to the following European Norms: •EN55022 (CISPR 22) - Radio Frequency Interference •EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity •EN60950 (IEC950) - Product Safety Five Year Warranty MiLAN Technology warrants to the original consumer or purchaser that each of its products, and all components thereof, will be free from defects in material and/or workmanship for a period of five years from the original factory date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable. MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in connection with the performance of the product delivered hereunder. MiLAN Technology will in no case cover damages arising out of the product being used in a negligent fashion or manner. Trademarks © 2000 MiLAN, the MiLAN logo, and MiLAN Technology are either trademarks or registered trademarks of Digi International, Inc. in the United States and/or other countries. All other trademarks are the property of their respective holders. To Contact MiLAN Technology For prompt response when calling for service information, have the following information ready: Product serial number and rev; date of purchase; vendor or place of purchase. You can reach MiLAN Technology technical support at: support@milan.com Telephone: +1.408.744.2751 Fax: +1.408.744.2771 MiLAN Technology 1299 Orleans Drive, Sunnyvale, CA 94089-1138 United States of America Telephone: +1.408.744.2775 Fax: +1.408.744.2793 info@milan.com © Copyright 2000 MiLAN Technology Printed in the U.S.A. Installation Follow the steps given below to install the MIL-C1111: 1. Attach a UTP cable from network to MIL-C1111’s RJ-45 port. 2. Attach a T-type BNC connector from network cabling to the BNC connector. 3. Plug the power adapter into an AC outlet and connect the power adapter cord to the unit. EMI Note: Use shielded UTP (CAT 5) cabling for CISPR 22 classB. Configuration-Termination Switch Next to the coax cable connector, there are DIP switches that control the 50 Ohm internal resistor. Both switches are shipped in the “up” position (default, no termination). Configuration Options 1. If the MIL-C1111 is connected to the end of a multinode segment without a T-connector and terminator, enable 50 Ohm resistor by • Setting switch 1 “up” • Setting switch 2 “down”. 2. If the MIL-C1111 is connected to a single-nod without a T-type connector and terminator on a coax cable of less than one meter’s length: • Set both switches in the “down” position. Note: For this configuration, you do not need a 50 Ohm terminator on the coax segment of the MIL-C1111’s BNC connector. ©Copyright 2000 MiLAN Technology PN 90000213 Printed in the USA MIL-C1111 Coax to Base-T (UTP) Media Converter Installation Guide MIL-C1111 Ethernet COAX to 10BASE-T IEEE 802.3 Compliant COAX ACTIVE COAX ENABLE POWER TX ACTIVE TX LINK 500 mA UTPCoax LEDs • TP ACT: Amber, indicates a packet activity on the 10BASE-T network. • COAX ACT: Amber, indicates a packet activity on the 10BASE2 network. • TP LINK: Green, there is a good link on the 10BASE-T network. • COAX ENAB: Green, coax connection is established. Cabling Options: MDI-X/MDI Switch The MDI-X/MDI switch is located on the side of the unit. This switch enables a quick configuration of the 10BASE-T port. Cables used when the switch is in the MDI-X position: • For a hub or repeater, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, 6 to 2). • For a workstation or PC, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, 6 to 6). Cables used when the switch is in the MDI position: • For a hub or repeater, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, 6 to 6. • For a workstation or PC, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, 6 to 2. RJ-45 Specifications MDI-X 1234 5678 MDI Pin 1=TX+ Pin 1=RX+ Pin 2=TX- Pin 2=RX- Pin 3=RX+ Pin 3=TX+ Pin 6=RX- Pin 6=TX ...