Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Press [MENU], select “User Manage”, press [OK], select “Enroll User”, press [OK], select “Enroll FP”, press [OK], the following appears: Enroll FP New Enroll? ESC OK Press [ESC] to cancel the new enrollment, enter the User ID (PIN number) of the user you wish to enroll an additional fingerprint for: Backup Enroll User ID 00001 ESC OK - 19 - Password Enrollment 1) Press [MENU], select “User Manage”, press [OK], select “Enroll User”, press [OK]. Three enrollment methods are displayed, select “Enroll Pwd”, press [OK]. The following screen is displayed: Enroll Pwd New Enroll? ESC OK 2) Press [OK] to enroll new user, the following screen is displayed: New Enroll User ID 00006 ESC OK 3) Note: The next available User ID is displayed. Press [OK] to choose this ID or enter a User ID (range is 1 to 65534) & press [OK]. The following screen is displayed: New Enroll Input Pwd_ ESC OK - 20 - 4) Input the password and affirm: New Enroll Input Pwd ***** Pwd Affirm ***** 5) Press [OK], the following screen is displayed: New Enroll 00006-P ESC OK (Save) Note: 00006-P “-P” means password enrollment 6) Press [OK]. Press [ESC] to exit user enrollment or press [OK] to continue Password enrollment. - 21 - Fingerprint & Password 1) Press [MENU], select “User Manage”, press [OK], select “Enroll User”, press [OK]. Three enrollment methods will be displayed, select “FP & Pwd”, press [OK]. The following screen is displayed: FP & Pwd New Enroll? ESC OK 2) Press [OK], the following appears: New Enroll User ID 00008 ESC OK 3) Press [OK], the following appears: New Enroll 00008-0 Place Finger… ESC/Exit - 22 - 4) If the test is successful three times in a row, the following appears: New Enroll 00008-0 Input Pwd ***** ESC OK 5) Input your password, the following appears: New Enroll 00008-0 Input Pwd ***** Pwd Affirm ***** 6) Input the password again, press [OK], the following appears: New Enroll 00008-0P ESC OK (Save) Note: 0000-0P; “-0P” indicates first fingerprint and password. 7) Press [OK], the previous message continues to be displayed while the template is created. - 23 - User Verification Types Fingerprint Verification There are (3) fingerprint verification (“authentication”) types: 1:1 Verification (“One to One” Verification) In this mode, a user enters their 5-digit User ID and takes a fingerprint reading. The TQ600 compares their fingerprint to the fingerprint template of the User ID that was entered, thus a 1:1 comparison. The 1:1 verification method is the fastest verification method since it only has to compare the user’s fingerprint to one template stored in the terminal. 1) In the initial interface, enter your ID number and the following appears: 1:1 FP Match User ID 00011 ESC OK Note: The User ID is 5 digits. If you enter a number with less than 5 digits the TQ600 adds 0’s in order to create a 5 digit User ID, i.e., if you enter “11” the TQ600 will Enroll “00011”. - 24 - 2) Press [OK] and the following appears: 3) It continues FP Verify User ID 00011 Place Finger… for about 0.5 seconds. If the test is successful, the following appears: Verify User ID 00011 Verified. 4) If your identity cannot be verified, you are prompted to try again, the following appears: 1:1 FP Match Please Try Agn. It continues for about 0.5 seconds then returns to the start-up window. - 25 - 1:N Verification (“One to Many” Verification) In this mode, a user simply takes a fingerprint reading. The TQ600 compares their fingerprint to all of the fingerprint templates stored in the terminal. 1:N verification takes more time than 1:1 verification. The verification time is dependent on the number of fingerprint templates stored in the terminal. 1) Place finger on the sensor surface, the following appears: FP Verify Remove Finger 2) It continues for about 0.5 seconds. If the test is successful, the following appears: Verify User ID 00001 Verified. 3) If your identity cannot be verified, you are prompted to try again, the following appears: FP Verify Please Try Agn. It continues for about 0.5 seconds, return to the start-up window. - 26 - Password Verification A password 1 to 5 digits long is used to validate authentication. Password verification can be used in special cases, i.e., when all of a user’s fingerprints are damaged. This method of verification does not provide the security of biometric identification and should only be used when absolutely necessary. Note: when a user with an enrolled password attempts (1:1) verification the TQ600 will ask for the User’s password and the user will not have the option of taking a fingerprint reading. 1) To verify a password, enter your ID number, the following appears: PWD Affirm User ID 00008 ESC OK 2) Press [OK], the following appears: Pwd Affirm User ID 00008 Input Pwd ***** 3) Input correct password, press [OK], the following appears: Verify User ID 00008 Verified. - 27 - 4) If the password cannot be verified, the following appears: Pwd Affirm Error Pwd. - 28 - 5 5 Enrolling – Proximity Terminals This chapter d...
Эта инструкция также подходит к моделям:Регистраторы времени - timeQplus TQ600 (420.43 kb)