Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Do not put a heavy object on the time recorder, or forcefullypress the time recorder onto the back-plate. This may cause trouble with the punching mechanism. Lithium battery contains perchlorate material – special handling may apply. Please go to the web site for information about proper methods of disposal. About this Manual This manual will guide you through the installation, set up and use of your 800P TruAlign Time Recorder. Optional Accessories . E8-100 Weekly timecard for the 800P (pack of 100) . 25-9EX Expanding timecard rack, 9” cards, 25 pockets Note: The E8 timecards are sensitive to temperature and should always be stored in a cool dry location preferably out of exposure to direct sun light. Storage temperature should not exceed 150oF (65oC). Page 6 800P TruAlign Time Recorder User Guide Packing Contents 800P Time Recorder(withback-plate) BracketWall-Mount Installation & User’s Guide AC Wall Adapter Sample pack of E8 timecards (2) #8 Philips Head screws for Wall-Mount Bracket (2) #8 Anchors (use for masonry wall installation only) (2) 8-32 x . Philips Head screws to install Back-Plate to Wall-Mount Bracket Recommended Installation Tools Pencil Tape Measure Philips Head Optional- Power Drill & Drill Bits Screw Driver Page 7 800P TruAlign Time Recorder User Guide Quick Easy Setup (Wall Mount) To setup your 800P, follow these next steps: Step 1 Separate the back-plate from the800P by removing the Philips head screw. Retain the screw for later. Step 3 Using the supplied 8-32 x . Philips head screws install the back-plate to the wall-mountbracket. Step 5 Align and place the 800P on theback-plate and secure the twotogether with the 8-32 x . Philiphead screw. Be careful not to pinch the AC cord. Note: Make sure the bottom of the timecard shelf is over the edge of theback-platebefore securing the screw. Step 2 Install the wall-mount bracket to the wall using the supplied wall-mount screws. Note: For best visibility mount the 800P about 48 inches from the floor. 48 inches Step 4 With the back-plate secured tothe wall-mount bracket, plugthe AC wall adapter into the 800P. Note: The time, date and other settings are factory set. See“Factory Settings” below. If these settings are acceptableyou are ready to begin, otherwise see Page 11“Programming the 800P”. Factory Settings . Time=U.S. Eastern Time . Daylight Savings=On . Spring Daylight Savings=Second Sunday in March . Fall Daylight Savings=First Sunday in November . Displayed Time Format=AM/PM hours & Minutes . Printed Time Format=AM/PM hours & Minutes . Day of Week Language=English . Confirmation Beep=Disabled Page 8 800P TruAlign Time Recorder User Guide Quick Easy Setup (Table Top Mount) To setup your 800P, follow these next steps: Step 1 Separate the back-plate from the800P by removing the Philips head screw. Retain the Philips head screw for later. Step 2 Plug the AC adapter into the 800P and then plug the walladapter into the AC outlet. Step 3 Secure the back-plate to the 800Pwith the Philips head screw being careful not to pinch the AC cord. Make sure the bottom of the timecard shelf is over the edge of the back- plate before securing the screw. Place the 800P on a solid flat surface. You are ready to begin using the 800P. Note: The time, date and other settings are factory-set. See “Factory Settings” to the right. If these settings are acceptable you are ready tobegin, otherwise see Page 11 “Programming the 800P”. FactorySettings Time=U.S. EasternTime DaylightSavings=On SpringDaylightSavings=SecondSundayinMarch FallDaylightSavings=FirstSundayinNovember DisplayedTimeFormat=AM/PMhours&Minutes PrintedTimeFormat=AM/PMhours&Minutes Day of WeekLanguage=English ConfirmationBeep=Disabled Page 9 800P TruAlign Time Recorder User Guide Setup To set up your 800Ptime recorder, follow these next steps: Remove the Back-Plate Separate the back-plate from the time recorder by removing the Philips head screw. Retain the Philips head screw for later. Connect the AC Power Plug the AC adapter into the time recorder and then plug the wall adapter into the AC outlet. NOTE: The time recorder has an internal battery that will retainthe programming if the time recorder is unplugged from AC power. Page 10 800P TruAlign Time Recorder User Guide Programming the 800P After removing the back-plate and connecting the AC power you will be ready to begin programming the 800P time recorder. Use the three buttons on the back to program thetime recorder. Hold the time recorder with both hands with the display facing you. Use your index and middle fingers to press the programming buttons on the back of the time recorder while watching the settings on the display. Note: An undisturbed environment is recommended when programming the timeclock. Using the 3 programming buttons + (Plus) When you press the + button, you increment or change the selected setting. SET You can set the value of the selected setting on the display by pressing the SE...