Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
This unit fits in a standard 2 1/8" (54 mm) hole used by most marine equipment manufacurers. Mounting The LDT-3003 mounts in any dash or flat panel that's at least 2 1/2" (64 mm) in diameter. To mount the unit, first make certain there is at least 3 3/4" (95 mm) from the front of the dash to any obstruction behind the dash. Also, be sure there is room to route the power and sensor cables. The maximum usable dash thichness is 1 1/8" (28.5 mm). 3 3/4" minimum TIGHTEN THESE SCREWS 1234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567123456712345671234567 DASH When you determine the location for the LDT-3003, drill a 2 1/8" (54 mm) hole in the dash. Slide the LDT-3003 through the hole from the front of the dash. Align it so that it's straight, then tighten the two screws with a phillips-head screwdriver. Place the pushbuttons into the holes in the bezel and snap it on to the LDT-3003. The unit is now ready for wiring. 1 TO TACH TO TO TACH TO ACCESSORY SWITCH GREEN BLUE WHITE RED BLACK SPEAKER TEMPERATURE FUSE SENSORS DASH RED BLACK YELLOW ORANGE 12-VOLT BATTERY DASH SPEAKER TO TACH TO TEMPERATURE SENSORS 2-AMP FUSE ACCESSORY SWITCH 12-VOLT BATTERY RED BLACK GREEN BLUE YELLOW WHITEORANGE LIGHT SWITCHRED BLACK 2 WIRING WIRING The unit won't be harmed if the power wires are connected backwards, however, it won't work until they're properly connected. Make certain to connect the green wire to unswitched +12 volts. This keeps power on to the unit's memory so that the clock will keep running even when the unit is switched off. Find a location for the speaker that is protected from the elements, but still lets you hear it.The typical mounting location is behind the dash. If the LDT-3003's wires won't reach the speaker, splice ordinary speaker wire to them. SENSORS The LDT-3003 can use the following sensors: TS-W2BK Two temperature sensors - Water and Temp 2. TS-3BK One temperature sensor - Temp 3 only. We reccommend you use the LDT-3003 with the above sensors in the following combination: One TS-W2BK. This gives you two temperature displays - Water and T2. or One TS-W2BK and one TS-3BK. This gives you three temperature displays - Water, T2, and T3. For example, you can connect the TS-W2BK temperature sensors and mount the sensor labeled "water" on the transom to measure surface water temperature and the sensor labeled "T2" in the live well or on the hull for outside air temp. The TS-W3BK has an extra connector so you can attach the TS-2BK temperature sensor to it, then attach the TS-3BK's connect to the LDT-3003 and have three separate temperature displays. 3 4 The temperature sensors can be mounted in any convenient location. Use #8 stainless steel screws to attach the sensor to the hull. (Screws not included.) When mounting the water temperature sensor as shown above, make certain to place it on the transom where it will be in contact with the water at all times, if possible. OPERATION Modes The LDT-3003 has a clock,a clock alarm, up to three temperature displays, an alarm for each temperature sensor, an engine hour meter, and a voltmeter. To switch between these modes, simply press the mode key. Clock When the unit is turned on, the clock appears as shown at right. A dot in the upper left corner of the screen is for a.m. or p.m. - it's your choice when you set the clock. The clock will continue to run even when the unit is turned off. Water Temperature The first temperature to appear after pressing the MODE key is the water temperature. This sensor is mounted on the transom. T2 Temperature The second temperature to appear is T2. This sensor can be mounted in a live well, on the hull to measure outside air temperature, or just about any other location. MODE MODE 5 T3 Temperature If you have the T3 temperature sensor installed, it appears after T2. This sensor can also be mounted in a live well, on the hull to measure outside air temperature, or just about any other location. Engine Hour Meter This shows the total number of hours the engine has operated. It senses the engine operation from the tachometer. The LDT-3003 must be turned on, however to record engine time. The engine hour meter cannot be reset. (Note: The engine must be running in order to view the hour meter.) Voltmeter The voltmeter shows the current electrical system voltage. MODE MODE MODE Setting the LDT-3003 The clock can be set to the correct time, alarms can be set to desired time and/or temperature (for each temperature probe), and the temperature displays can be set to °F or °C. The LDT-3003 has a "set" mode that cycles through all of these settings, starting with the clock. To set any of these features, simply press the SET key repeatedly until the desired function appears that you wish to change, then press the MODE key t...