Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
ATOMIC CLOCK WITH TWO LINE DISPLAY • Time, Date, Day, Moon Phase, Temperature and Time Zone B. PROJECTOR • Projects current time or temperature onto the wall or ceiling. • Rotates to project on wall or ceiling. C. SNOOZE/LIGHT button • Activates snooze feature and amber backlight for 5 seconds. D. LIGHT SENSOR • Activates continues projection at low light conditions (less than 100LUX) when power adapter is connected. 5 REAR VIEW M E F G H I L K J E. DOWN arrow button ( Ў ) • Decreases all function parameters • Activates the atomic time signal reception when pressed and held with UP( ^ ) button • Press & Hold to select the language for day of the week (English, French, Italian, Spanish, German) . F. UP arrow button ( ^ ) • Increases all function parameters. • Activates the atomic time signal reception when pressed and held with DOWN( Ў ) button • Press to select either 12 or 24 hour time format • Activates US Time Zone selection mode. 6 G. MODE button • Press to select: ALARM 1, ALARM 2 or Temperature • Press & hold for 2-3 seconds to set the date and time manually. button H. SET • Allows programming ALARM 1 and its snooze interval • Activates or deactivates ALARM 1 I. SET button • Allows programming ALARM 2 and its snooze interval • Activates or deactivates ALARM 2 J. BATTERY COMPARTMENT Accommodates 2 (two) UM-3 or AA 1.5V alkaline batteries K. FLIP BUTTON • Press to flip the projected image 180° . • Press and hold for 2-3 seconds to alternate projection display between time & temperature L. FOCUS knob Allows adjusting the projected image sharpness M. ROTATE knob Allows rotating of the projected image clockwise or counterclockwise SIDE VIEW N O 7 N. “ CONTINUE PROJECTION” switch Activates the continuous projection function O. AC/DC ADAPTER INPUT Provides power via AC/DC adapter GETTING STARTED • We recommend using alkaline batteries. • Avoid using rechargeable batteries as they may not provide appropriate power levels. • Insert batteries and power adapter before use. IMPORTANT NOTES: 1). The Atomic Projection Clock does not work without the batteries installed, even if AC adapter is connected. 2). Continuous projection is designed to work only at lower light conditions (at 100LUX and lower) During the day to check if continuous projection works, slide the “CONTINUE PROJECTION” switch to the UP position, cover the light sensor with the palm of your hand when AC adapter connected and batteries are installed. BATTERY INSTALLATION • Open the battery compartment door. • Install 2 batteries (UM- 3 or “ AA” size 1.5V) matching the polarity as shown in the battery compartment. • Replace the battery compartment door. NOTE: Unit will display a “Low Battery” indicator when batteries age. 8 WWVB RADIO CONTROLLED TIME The NIST (National Institute of Standards and Technology) radio station ( WWVB) is located in Ft. Collins, Colorado. It transmits an exact time signal continuously throughout the most of the continental United States at 60 KHz frequency. The Atomic Projection Clock can receive this WWVB signal through the internal antenna from up to 2,000 miles away. Due to the nature of the Earth’s ionosphere, reception can be limited during the daylight hours. The radio controlled clock will search for an alternate station that receives the atomic time signal from the NIST Atomic clock in Boulder, Colorado. The WWVB tower icon on the unit’s display will flash indicating a radio signal reception from the WWVB station. If the tower icon is not fully lit, or if the time and date are not set automatically, please consider the following: • During night- time hours, atmospheric disturbances are typically less severe and radio signal reception may improve. A single daily reception is sufficient enough to keep the clock accuracy within 1 second. • Make sure the unit is positioned at 8 feet (2 meters) distance from any interference source such as a TV, computer monitor, microwave, etc. • Within concrete wall rooms such as basements or office buildings, the received signal may be weakened. Always place the Atomic Projection Clock near the window for better reception. ATOMIC CLOCK OPERATION Immediately after installation of batteries, the clock will beep and display all available LCD segments for a moment. Then the atomic time signal receiver will start searching for the atomic time signal. It usually takes between 5-8 minutes. NOTE: Do not press any buttons on the unit during auto search as it may 9 interrupt product’s operation, and you will need to start the set up procedure again. If the reception is successful and the atomic time signal is received, the date and time will be set automatically, and the [ ] icon will appear on the display. NOTE: It is necessary to set your Time Zone, keeping in mind that the default zone is a Pacific Standard Time (PST). ( Refer to MANUAL SETTINGS section) If the initial reception was not successful and the time signal has not been received in this first 8 minutes, you may press and hold the UP...