Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Orbit Manufacturing, модель Fluid 91916

Производитель: Orbit Manufacturing
Размер: 1.71 mb
Название файла:
Язык инструкции:enes
Перейти к скачиванию



Фрагмент инструкции


If the remote is not functioning properly or if you are adding a new remote or RF sensor to your system do the following: • With the remote device in your hand press the “RF Sync” button on the timer (this will activate a red light on the timer). • Press the OFF button on the remote or depress the stem of the RF sensor (the red light should start blinking). • If the red light blinks you have successfully synchronized the devices. If the light does not blink check that the remote has a fresh 9V battery or that the RF sensor switch is not OFF and try the steps again. To Water All Stations: • Press and release the ALL button on the remote control device to select all stations for watering. • Press and release the ON “X” MIN button to command the timer to water all the stations sequentially for the desired (“X”) number of minutes. • If you wish to advance to the next station before a station's watering duration is complete, press NEXT. To Water One Station: • Press the number of the station you wish to water. • Press ON "X" MIN to water the station for the desired ("X") number of minutes. To Water More Than One Specific Station: • Press the numbers of the stations you wish to water. (Example: 3, 7, 10, and 6. The timer will water in sequence from lowest to the highest. 3, 6, 7, 10.) (No matter which order you press the keys, the timer will water them sequentially from the lowest to the highest number.) • Press ON “X” MIN to water those stations for the desired (“X”) number of minutes. To Cancel Remote Control Device Operation and Return Control to Timer: • Press the OFF/CLEAR button on the Remote Control Device. This cancels any current commands from the device and returns control back to the timer. Section 5: Using the Optional Rain-Freeze Sensor An optional rain-freeze sensor can be purchased separately to prevent programmed watering for a specified period of time after rain falls or during periods when temperatures fall below a specified temperature. The sensor has settings for RAIN, OFF and RAIN/FREEZE. Please refer to the manual that accompanies the rain-freeze sensor for installation and programming instructions. NOTE: The rain-freeze sensor will function only when the selection dial on the timer is turned to AUTO. Section 6: Installing Indoor Mount Sprinkler Timer and Remote Control Device Sleeve NOTE: Before installation, please have the following tools on hand: • Phillips screwdriver • Wire strippers Installing the Sprinkler Timer in Five Easy Steps 1. Select a Location Select a location with the following criteria: • Near an electrical outlet. (Avoid using an outlet controlled by a switch.) • In a dry, indoor location, where operating temperatures are not below 32° or above 122° Fahrenheit (below 0 degrees or above 50 degrees Celsius). • Not in direct sunlight. • Accessible to sprinkler wires from valves. Slide the Timer off the Docking PortSENSORCOMPUMP12345678910111224 VACRF SYNCACTIVEBYPASSNO WATERINGDAY / PERIOD Figure 3: Mounting the Docking Port 2. Mount the Docking Port • Slide the timer off the docking port. (See Figure 3) • Using the mounting template (included), mark the two screw locations on the wall, then drill holes at the marks for No. 8 screws. Use the expanding anchors in plaster or masonry if necessary. • Place the docking port against the wall, aligning the two holes in the docking port with the two drilled holes. • Secure the docking port to the wall by screwing a No. 8 screw (included) through each of the two holes. • Do not slide the timer back onto the docking port yet. 3. Connect the Transformer • Find the two sockets at the bottom of the docking port labeled “24VAC.” (See Figure 4) • Insuring the transformer is not plugged in; insert one of the two power leads from the transformer into each terminal socket using the phillips screwdriver to depress the terminal button (this allows for wire insertion or removal). • Plug in the transformer. WARNING: Do not link two or more sprinkler timers together with one tran...

Эта инструкция также подходит к моделям:
Регистраторы времени - Fluid 57912 (1.71 mb)
Регистраторы времени - Fluid 57916 (1.71 mb)
Регистраторы времени - Fluid 57922 (1.71 mb)
Регистраторы времени - Fluid 57926 (1.71 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории