Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If the time or date is not correct, press [*] to cancel and try again. The display will now show the time and date you just entered. You can toggle between the 12-hour and 24-hour display using “Quick Check” command [3] Make sure you enter the correct date and day, because the schedules you setup depend on these choices [2]=Select Clock Control This function requires the administrator password Use this function to choose the make/model of the clocks that your Master will synchronize (Note: The LTR4-512 can only synchronize one type of secondary system) Enter your administrator password, then start this function by pressing [#][2][#] Enter the 2-digit code for CLOCK1, then press [#]. If you entered a code other than ‘00’, and you have a LTR8-512 or LTR8-512M, you will see Enter the code for CLOCK2, or [0][0] if you will not use a CLOCK2, then press [#] PRESS [#] IF CORRECT Enter [#] to confirm or [*] to cancel and try again Text Box: ENABLE CLOCK CIRCUIT SELECT CLK1 CODE: NN [#] FOR CODE LIST Text Box: ENABLE CLOCK CIRCUIT SELECT CLK2 CODE: NN [#] FOR CODE LIST Text Box: ENT.DATE: 04-03-2003 TODAY IS THURSDAY ENTER TIME: 21:00 PRESS [#] IF CORRECT [3]=Manual Bell Control This function does not require a password Use this function to test bell circuits or to sound a bell during an unscheduled time, such as a fire alarm. Press [#][3][#] to start this function The 2nd line of the display only shows the circuit numbers (1-8) that are available for bell controls Press [0] to turn them all off, or press keys [1] - [8] to turn a circuit off or on When you see the circuits that you want to ring, press and hold the [#] key. The green front panel lights will light up to show that you have turned on those relays. Release the [#] key to turn those relays back off. Note that the relays scheduled to turn ‘on’ will cycle as programmed You can now sound other circuits, or press [*] to quit Note: When your CLOCK1 Type is Type 14 (Electronic Coded) or Type 15 (Straight Frequency), you may need to hold the [#] key for about a minute to energize your bell circuits. You will know that your circuits have turned on when the green front panel lights for those circuits light up [4]=Program Schedules Use this function to set bell schedules. A schedule lists the days and times when the bell circuits will turn on. Your Master can have up to eight (8) different bell schedules with up to sixty-four (64) ‘events’ per schedule. If needed, you can make several schedules active at the same time to increase the number of events to as many as 512 (8 multiplied by 64). In fact, each ‘event’ can trigger several ‘actions’. For example, you can program a single event to turn on relays #1, #2 and #4 for 7 seconds at 08:00 AM on Tuesdays, Thursdays and Holidays Enter your password (#0#), then press [#][4][#] to start programming schedules Text Box: MANUAL BELL CONTROLS 1-2-3-4-5-6-7-8 PRESS AND HOLD [#] TO EXECUTE.[*]TO END Text Box: SCHEDULE PROGRAMMING SELECT SCHEDULE # N Press Schedule Number [1] - [8]. Normally, start with [1] The following will show on the display: For Firmware version 4.05 and earlier: For Firmware version 4.06 and later: To select the appropriate mode: Press [1] DATA ENTRY to create a new schedule Press [2] DATA SCAN to view a schedule Press [3] DATA EDIT to change a schedule Press [4] CLEAR to clear all records in the selected schedule When you choose [2] DATA SCAN, you can view events. You can use these scan keys: Scan Key Description [9] 1ST Go to the 1st event (in ascending time order) [3] PRV View the previous event [#] NXT View the next event [*] EXIT End and exit When you choose [3]DATA EDIT, you can view, edit or delete events. You can use the keys above, plus these edit keys: Edit Key Description [1] EDIT Edit the displayed event [4] DEL Delete the displayed event [6] ADD Add a new event When you choose [1]DATA ENTRY, you can create a schedule. Follow the steps below to create a schedule Text Box: SELECTED SCHEDULE # 1 SELECTED MODE = ENTRY ZONE TYPE = BELL PRESS [#] TO EXECUTE Press [#] to accept. Then select the days when this event occurs [0] selects no days, [1]-[7] selects Sunday-Saturday, [8] selects holidays and [9] selects all days (including holidays). Press these keys to turn days on or off. After you choose the days when the event will occur, press [#] Example: Press 1,3,5,7,8 to turn off all days except Monday, Wednesday and Friday Select which circuits will turn on for this event Example: Press 1,2,3,4, to turn on circuits 1, 2, 3 and 4 Enter the event start time in 12-hour or 24-hour format. If you enter a time earlier than 13:00 (1:00 PM), then press [1] to change PM to AM The menu will ask for the bell length (SECONDS ON) Enter how many seconds this event lasts. The bell length shows 3 seconds (or 5 seconds if your CLOCK1 is Type 15). To accept, press [#], or enter another value from 01-99 seconds, then press [#] Your Master saves these values in the schedule then displays SELECT DAYS again, waiting f...
Эта инструкция также подходит к моделям:Регистраторы времени - LTR8-512 (876.02 kb)
Регистраторы времени - LTR8-512M (876.02 kb)