Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
To install and replace the batteries, please follow the steps below: 1. Pull down on the tab at the top of the battery cover and lift up to remove the cover. 2. Insert batteries observing the correct polarity (see marking inside battery compartment) . 3. Replace compartment cover. DO NOT SET THE CLOCK. SETTING UP: Alkaline batteries are recommended for use. Avoid using rechargeable batteries. 1. Place batteries in the atomic clock. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. 2. After 15 minutes the indoor area on your clock should have a temperature and humidity showing. If not, remove batteries, wait 15 minutes and repeat step one. 3. After the clock receives the WWVB time code reception will automatically start. This reception typically takes between 5-10 minutes in good conditions. If after 15 minutes the WWVB time has not been received, use the “SET” key to manually enter the set-up mode and change either the time or date in order to activate the WWVB reception (see manual settings below). The clock will then automatically attempt to receive the WWVB time from 12: 00 am through 6: 00 am each day (attempts WWVB reception every full hour within this time frame) . When this is successful, the received time will override the manually set time. The date is also updated with the received time (Please refer to notes on “ Radio controlled time” and “ Manual time setting”). 4. After the time signal has been received or the search mode has been manually stopped the indoor temperature will be displayed. Note: When changing batteries in the unit, ensure that the batteries do not spring free from the contacts. Always wait at least 15 minutes after removing the batteries before reinserting, otherwise start up problems may occur. FUNCTION KEYS The atomic clock has four easy to use keys: SET key : To enter into the set mode for the following functions: LCD contrast, time zone, DST ON/ OFF (daylight saving time), radio-controlled time ON/ OFF, language, hour, minute, year, month and date. 2 3 Indoor humidity and temperature Second Display + key : To change any values in manual set mode or alarm set mode ALM key : To enter into the alarm set mode To set the alarm ON/OFF To display the alarm time in normal mode display To exit the setting modes SNZ key : To activate the snooze function during alarm ATOMIC CLOCK LCD SCREEN DESCRIPTIONS The atomic clock's LCD is divided into 2 sections and once the batteries are inserted, all the segments will light up briefly before displaying the information for time, date, indoor temperature, indoor humidity, and second. MANUAL SETTINGS Note: If the atomic clock has already successfully received the WWVB time signal and displays the correct time and date, then the Manual settings can be skipped. WWVB time Radio reception icon Weekday Date Alarm icon Month Moon Phase Display Af t e r comple t i on of t he abov e describe d pro c edure s in “ Se tti ng up” t h e manu al sett ing modes can be e n t e r ed by pressing and holdin g t h e SET ke y f o r 5 s e c o n d s. T h e f o l l o wi n g s e t t i n gs c a n now be programmed: • LCD contrast setting • Time zone setting • DST ON/ OFF • Radio-controlled time ON/ OFF • Language display setting • Manual time setting (Hour then Minute) • Year setting • Month setting • Date setting LCD CONTRAST SETTING Default (Factory) Setting 4 -5 (Eastern Standard Time) ON ON ENG (English) 12 (hour), 00 (minute) 2004 Jan (January) 1 After entering the manual setting mode as described above, the LCD contrast can be set between 0 and 7. 1. Press and hold the SET key for 5 seconds. 2. LCD will be displayed in the lower display and a number will flash to the right of the word LCD. 3. Press and release the + key to select the desired LCD contrast. 4. Press and release the SET key to confirm the LCD contrast and continue to the Time Zone setting. TIME ZONE SETTING The time zone can be set between the –1 to –12 hour or Greenwich Mean Time (GMT) range. 1. The time zone will start flashing (Default setting "-5h“ ) in the lower LCD display. 4 2. Press and release the + key to select the desired time zone. 3. Press and release the SET key to confirm the time zone setting and continue to the DST (Daylight Saving Time) setting. Note: The time zones from –4 to –10 hours will be displayed with 3 characters abbreviations: • -4 ATL (Atlantic time), • -5 EST (Eastern time; default time zone) , • -6 CST (Central time), • -7 MST (Mountain time), • -8 PST (Pacific time), • -9 ALA (Alaska time), • -10 HAW (Hawaii time). • "GMT” will be displayed if set to GMT (0). DST SETTING ( daylight saving time) 1. The word ON will start flashing in the lower LCD display. 2. Press and release the + key to select DST ON or OFF. 3. Press and release the SET key to confirm the DST setting and continue to the Radio- controlled time setting. Note: The DST default is “ON”, meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall. For areas that ...