Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
ALARM ON / OFF (at the top): Enable / disable alarm 3. Time zone 4. Clock signal reception indicator 5. Clock, alarm and temperature display 6. °C / °F temperature unit display 7. Alarm icon 8. Outdoor temperature icon 9. Battery low indicator 10. Indoor temperature icon 11. Projector: Project time,alarm status and indoor / outdoor temperature BACK VIEW 1. FOCUS: Focus the projected image 2. Adaptor socket 3. Battery compartment 4. EU / UK: Select clock reception 5. PROJECTION AUTO / CLOCK / OFF: Select the projection mode 6. 180° ROTATION: Rotate projection image by 180° degrees 7. SET ALARM: Set alarm 8. SET CLOCK: Enter clock setting mode 9. °C / °F: Select temperature unit 10. / : Increase / decrease settings; activate / deactivate clock reception signal 11. RESET: Reset unit to default settings REMOTE SENSOR 1. LED status indicator 2. Wall mount hole 3. Battery compartment 4. RESET hole 5. CHANNEL switch GETTING STARTED POWER SUPPLY Batteries serve as back up. For continuous use of projector and backlight, always plug in the adapter socket. Make sure the socket outlet is easily accessible to the unit. To insert batteries: 1. Remove the battery compartment and insert the batteries, matching the polarities. 2. Press RESET after each battery change. indicates main unit batteries are low. REMOTE SENSOR To set up the sensor: 1. Open the battery compartment. 2. Select a channel then press RESET. 3. Close the battery door. 4. Place the sensor within 30 m (98 ft) of the main unit using the table stand or wall mount . TIP The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results. SENSOR DATA TRANSMISSION The main unit will automatically search for the outdoor sensor. The sensor reception icon in the remote sensor area shows the status: ICON DESCRIPTION Main unit is searching for sensor(s). A channel has been found. Sensor 1 data received. and “--.-“ The sensor cannot be found. NOTE If the sensor is not found, check the batteries, obstructions and remote sensor location. For best results: • Place the sensor out of direct sunlight and rain. • Position the sensor facing the main unit, minimizing obstructions. • Place the sensor in a location away from metallic or electronic objects. • Position the sensor closer to the main unit during cold winter months. CLOCK CLOCK RECEPTION This product is designed to synchronize its clock automatically with a clock signal. DP200: Slide EU / UK to select the signal received. • EU: DCF-77 signal: within 1500 km (932 miles) of Frankfurt, Germany. • UK: MSF-60 signal: within 1500 km (932 miles) of Anthorn, England. DP200A: • WWVB-60 signal: within 3200km (2000 miles) of Fort Collins Colorado. To enable / disable signal reception: Press and hold to enable or to disable signal reception. NOTE Reception takes 2-10 minutes. If the signal is weak, it can take up to 24 hours to get a valid signal. Clock signal reception indicator: STRONG SIGNAL WEAK SIGNAL NO SIGNAL MANUALLY SET CLOCK To set the clock manually, disable the signal reception fi rst. 1. Press and hold SET CLOCK. 2. Press or to change the settings. 3. Press SET CLOCK to confi rm. 4. The settings order is: time zone offset, 12/24 hr format, hour and minute. DP200: Time zone offset sets the clock +/- 23 hours from the received clock signal time. LCD DISPLAY Wave your hand at least 3 inches above the IR motion sensors to toggle display modes between: • Clock • Alarm • Outdoor temperature • Indoor temperature ALARM To set the alarm: 1. Press and hold SET ALARM. 2. Press / to set hour / minute. 3. Press SET ALARM to confi rm. indicates alarm is ON. To toggle alarms ON / OFF: 1. Press SET ALARM to display alarm time. 2. Press ALARM ON / OFF to turn alarm ON / OFF. To silence the alarm: • Wave your hand above the IR motion sensors to silence it for 8 minutes. OR • Press ALARM ON / OFF to turn the alarm off and activate it again after 24 hours. PROJECTION The ultra-bright LED enables daylight projection of time and temperature information. To activate projection: Slide PROJECTION to AUTO or CLOCK. • Slide to AUTO to toggle between current time and indoor / outdoor temperature. • Slide to CLOCK to project current time only. To adjust the projection image: • Press 180° ROTATION to rotate the image by 180°. • Focus the projector image by turning the FOCUS wheel. NOTE The installed CDS light sensor inside the unit will activate automatic projection / display dimming. NOTE If projection is illuminated, do not look directly into the projector. Oregon Scientifi c will not be held responsible for any results or consequences arising from the misuse of this product. TEMPERATURE To toggle temperature unit: Press °C / °F. NOTE Please keep the temperature sensor (adjacent to the adaptor socket) away from the main unit or electrical devices as heat from these devices will affect accurate indoor temperature readings. RESET Press RESET to return to the default settings. PREC...
Эта инструкция также подходит к моделям:Регистраторы времени - DP200A (653.45 kb)